Categories

What Are the Hole Processing Methods? What Are the Ways of FPC Hole Processing

Through holes in Flexible Printed Circuits (FPC) can be processed by CNC drilling just like those in Printed Circuit Boards (PCBs), but this method is not suitable for hole processing of tape-and-reel double-sided metallized hole circuits.
Jun 4th,2026 153 Views
Through holes in Flexible Printed Circuits (FPC) can be processed by CNC drilling just like those in Printed Circuit Boards (PCBs), but this method is not suitable for hole processing of tape-and-reel double-sided metallized hole circuits. With the increasing density of circuit patterns and the miniaturization of metallized hole diameters, coupled with the inherent aperture limit of CNC drilling, many new drilling technologies have been put into practical application. These new drilling technologies include plasma etching, laser drilling, micro-aperture punching, chemical etching, etc., which can better meet the hole forming requirements of the tape-and-reel process than CNC drilling. Below we briefly introduce three main methods for FPC through hole processing:

1. CNC Drilling

Most of the through holes drilled in double-sided FPCs are still processed by CNC drilling machines at present. The CNC drilling machines used for FPC are basically the same as those for PCB, but the drilling conditions are different. Due to the ultra-thin thickness of Flexible Copper Clad Laminate (FCCL), multiple layers can be stacked for drilling. If the drilling conditions are well optimized, even 10 to 15 layers can be stacked and drilled simultaneously.
For the backing board and cover sheet, paper-based phenolic laminate or glass fiber cloth epoxy laminate can be used, and aluminum plates with a thickness of 0.2~0.4mm are also fully applicable.
Drill bits for FPC drilling are commercially available, and drill bits for PCB drilling and milling cutters for profile milling can also be used for FPC processing. The processing conditions for drilling substrate holes, milling the profiles of cover films and stiffeners are basically the same. However, the adhesive used in FCCL is soft, so it is very easy to adhere to the drill bit. This requires frequent inspection of the drill bit condition and an appropriate increase in the drill bit rotation speed. Special care must be taken for drilling of multilayer FPC or Rigid-Flex PCB (R-FPC).

2. Punching

Punching of micro-apertures is not a new technology and has been used for mass production for a long time. Since the tape-and-reel process is continuous production, there are many cases of using punching to process through holes in tape-and-reel products. However, batch punching technology is limited to punching holes with a diameter of 0.6~0.8mm. Compared with CNC drilling, it has a longer processing cycle and requires manual operation. Since the size processed in the initial process is quite large, the corresponding punching die is also large, resulting in an extremely high die cost. Although it is beneficial to cost reduction in mass production, it bears a heavy burden of equipment depreciation, and cannot compete with CNC drilling in terms of small-batch production and flexibility. For these reasons, it has not been widely used so far.
In recent years, great progress has been made in both die precision of punching technology and CNC drilling, making the practical application of punching in FPC very feasible. The latest die manufacturing technology can produce dies capable of punching holes with a diameter of 75um in adhesive-free FCCL with a substrate thickness of 25um, with quite high punching reliability. If the punching conditions are appropriate, holes with a diameter of 50um can even be punched. The numerical control of punching devices and the miniaturization of dies can be well applied to FPC punching. However, neither CNC drilling nor punching can be used for blind via processing.

3. Laser Drilling

The finest through holes can be drilled with laser. Laser drilling machines for FPC through hole drilling include excimer laser drilling machines, pulsed CO2 laser drilling machines, YAG (Yttrium Aluminum Garnet) laser drilling machines, argon laser drilling machines, etc. Pulsed CO2 laser drilling machines can only drill the insulating layer of FCCL, while YAG laser drilling machines can drill both the insulating layer and copper foil of FCCL, with a significantly faster drilling speed for the insulating layer than for copper foil. It is impossible to achieve high production efficiency if all drilling processes are performed with only one laser drilling machine. Generally, the copper foil is etched first to form the hole pattern, and then the insulating layer is removed to form the through hole. In this way, extremely small aperture holes can be drilled with laser. At this time, however, the position accuracy of the upper and lower holes may restrict the drillable aperture. For blind via drilling, as long as the copper foil on one side is etched away, there is no problem with the position accuracy of the upper and lower holes.
At present, the finest holes are processed by excimer laser. Excimer laser is ultraviolet light, which directly breaks the structure of the base resin and disperses the resin molecules with minimal heat generation. Therefore, the thermal damage to the area around the hole can be limited to the minimum range, with smooth and vertical hole walls. If the laser beam can be further narrowed, holes with a diameter of 10~20um can be processed. Of course, the larger the board thickness to aperture ratio, the more difficult the wet copper plating will be. The problem with excimer laser drilling technology is that the decomposition of polymers will produce carbon black attached to the hole wall. Therefore, certain measures must be taken to clean the surface to remove carbon black before electroplating.
In addition, there are certain problems with the uniformity of the laser when processing blind vias, which will result in bamboo-shaped residues. The biggest difficulty of excimer laser is the slow drilling speed and extremely high processing cost, so it is only limited to the processing of high-precision and high-reliability micro holes.
Pulsed CO2 laser generally uses CO2 gas as the laser source and radiates infrared light. Unlike excimer laser, which burns and decomposes resin molecules through photochemical effect, it processes through thermal decomposition, resulting in much poorer hole shape than excimer laser. It can process holes with a diameter of basically 70~100um, but the processing speed is significantly faster than that of excimer laser, with much lower drilling cost. For pulsed CO2 laser, attention should be paid that when processing blind vias, the laser can only be emitted to the copper foil surface, and there is no need to remove the organic matter on the surface at all. To stably clean the copper surface, chemical etching or plasma etching should be used as post-treatment. Considering the technical feasibility, there is basically no difficulty in applying the laser drilling process to the tape-and-reel process, but it does not have an advantage when considering the balance of processes and the proportion of equipment investment.
About Maxipcb
Maxipcb empowers innovators to turn cutting-edge technologies into reality.
We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.