Altium Designer Layer Introduction
I. Layer Definitions
-
TopLayer: The top routing layer, used to draw the electrical connection lines between components.
-
BottomLayer: The bottom routing layer, with the same function as the top routing layer.
-
MidLayer1 (Mid Layer 1): Its function is that electrical connection lines are also drawn on this layer when making multilayer boards, but multilayer boards have relatively high cost. When using multiple layers, it is only necessary to add them again at the top and bottom positions.
-
MechanicalLayers: Can be used to draw the outline of the PCB printed board and the areas that need holes, and can also be used to annotate PCB dimensions, etc. Can be used to draw the outline of the PCB printed board and the areas that need holes. Note that the PCB outline, cutout areas, and PCB annotation dimensions should not use the same mechanical layer. For example, Mechanical Layer 1 is used to draw the PCB outline and cutouts, and Mechanical Layer 13 is used to annotate dimensions, etc. After separation, the technical personnel of the PCB manufacturer will analyze according to the contents of this layer whether this layer needs to be produced.
-
TopOverlay (yellow): The characters on the front side of the board, corresponding to TopLayer. For a single-sided board, only this layer of characters is needed. BottomOverlay (brown) corresponds to BottomLayer and is the characters on the back side of the board. For a double-sided board, the above two character layers are used.
-
KeepOutLayer: Its function is to draw the prohibited routing area. If no mechanical layer is drawn in the printed board, the PCB manufacturer's personnel will treat this layer as the PCB outline. If both the KEEPOUTLAYER and the mechanical layer exist, by default the mechanical layer is used as the PCB outline, but the PCB manufacturer's technical personnel will distinguish them themselves. However, if they cannot distinguish them, they will default to using the mechanical layer as the outline layer.
-
Multilayer (silver): Includes all routing layers. Generally, through-hole pads for single-sided and double-sided boards are on this layer. The drawn lines are drawn on all layers.
II. Layer Classification
2.1 Signal Layers
AD provides 16 signal layers: Top, Bottom, and Mid1-Mid14 (14 intermediate layers).
Signal layers are the routing layers used to complete the copper foil traces of the printed circuit board. When designing a double-sided board, generally only the Top and Bottom layers are used. When the number of PCB layers exceeds 4, Mid routing layers need to be used.
2.2 Internal Planes
AD provides Plane1-Plane4 (4 internal power/ground planes). Internal power/ground planes are mainly used for PCBs with more than 4 layers as dedicated routing layers for power and ground. Double-sided boards do not need to use them.
2.3 Mechanical Layers
Mechanical layers are generally used to draw the border (boundary) of the printed circuit board. Usually only one mechanical layer is needed. There are Mech1-Mech4 (4 mechanical layers).
2.4 Drill Layers
There are 2 layers in total: “Drill Drawing” and “Drill Guide”. They are used to draw drill hole diameters and hole positioning.
2.5 Solder Mask
There are 2 layers in total: Top and Bottom. What is drawn on the solder mask layer is the protection area around the pads and vias on the printed circuit board.
2.6 Paste Mask
There are 2 layers in total: Top and Bottom. The paste mask layer is mainly used for printed circuit boards with surface-mount components. At this time, it is required by the mounting process of surface-mount components. It is not needed when there are no surface-mount components.
2.7 Silkscreen
There are 2 layers in total: Top and Bottom. The silkscreen layer is mainly used to draw text descriptions and graphic descriptions, such as the outline, designators, and parameters of components.
2.8 Other Layers
There are 8 layers in total: “Keep Out”, “MultiLayer (all layers of the PCB board)”, “Connect”, “DRC Error”, 2 “VisibleGrid” layers, “Pad Holes”, and “ViaHoles”. Some of these layers are used by the system itself. For example, VisibleGrid is for the designer's convenience in positioning when drawing. Keep Out is used during automatic routing and is not needed for manual routing.
2.9 Toppaste: Top paste layer
2.10 Bottompaste: Bottom paste layer: refers to the exposed copper foil that we can see.
2.11 Topsolder: Top solder mask layer
2.12 Bottomsolder: Bottom solder mask layer: contrary to the toppaste and bottompaste layers, this is the layer to be covered with green oil.
2.13 Drillguide: Via guide layer
2.14 Drilldrawing: Via drill drawing layer
2.15 Multiplayer: Multilayer: refers to all layers of the PCB board.
