Categories

How PCB Design Solves Signal Integrity Issues

Aug 10th,2026 80 Views

1. How to select PCB laminate materials?

Selecting a PCB laminate must strike a balance among design requirements, manufacturability, and cost. Design requirements include both electrical and mechanical aspects. The choice of material becomes particularly critical for very high‑speed boards (frequencies above GHz). For example, the commonly used FR‑4 material exhibits significant dielectric loss at several GHz, which can severely attenuate signals and may make it unsuitable. From an electrical perspective, pay attention to whether the dielectric constant and dielectric loss are appropriate for the intended operating frequency.

2. How to avoid high‑frequency interference?

The basic approach to avoiding high‑frequency interference is to minimise the electromagnetic field coupling of high‑speed signals, i.e., crosstalk. This can be done by increasing the spacing between high‑speed and analogue signals, or by adding ground guard traces or shunt traces adjacent to analogue signals. Also, pay attention to noise coupling from the digital ground to the analogue ground.

3. In high‑speed PCB design, how do you solve signal integrity problems?

Signal integrity is essentially a matter of impedance matching. Factors affecting impedance matching include the driver architecture and output impedance, the characteristic impedance of the trace, the load characteristics, and the trace topology. The solutions are termination schemes and adjusting the trace topology.

4. Can a ground trace be placed between differential signal pairs?

Generally, you should not place a ground trace between differential signals. The key principle of differential signalling is to exploit the benefits of mutual coupling between the two lines, such as flux cancellation and noise immunity. Adding a ground trace in between would disrupt that coupling.

5. Is it necessary to add ground shielding traces on both sides of a clock trace?

It depends on the crosstalk/EMI situation on the board. If not handled properly, shielding traces can actually make things worse.

6. In Allegro layout, how do you handle the appearance of segmented traces (with small square boxes)?

This issue occurs because after module reuse, the tool automatically creates a named group. The key is to dissolve that group. In Placement Edit mode, select the group and then dissolve it. After that, you can move all the small‑box traces by entering the "ix 0 0" command.

7. How can we meet EMC requirements without incurring excessive cost?

The added cost on the PCB due to EMC typically comes from adding more ground layers to enhance shielding, and from using ferrite beads, chokes, and other components to suppress high‑frequency harmonics. In addition, mechanical shielding structures are often required to pass the full system EMC tests.

Below are some PCB layout techniques to reduce electromagnetic radiation:

  1. Choose devices with slower slew rates where possible, to reduce high‑frequency components of the signals.

  2. Place high‑frequency components away from external connectors.

  3. Ensure proper impedance matching for high‑speed signals, and pay attention to trace layers and return current paths to minimise reflections and radiation.

  4. Place adequate and appropriate decoupling capacitors at the power pins of each device to suppress noise on power and ground planes. Pay special attention to capacitor frequency response and temperature characteristics.

  5. Near external connectors, the ground can be partitioned appropriately, and the connector ground should be connected directly to chassis ground.

  6. Use ground guard or shunt traces adjacent to particularly high‑speed signals, but be aware of their impact on trace characteristic impedance.

  7. Keep the power plane recessed by 20H from the ground plane, where H is the distance between the power and ground planes.

8. For 2 GHz and above high‑frequency PCB design, what rules should be followed for microstrip design?

RF microstrip design requires the use of 3D electromagnetic field simulation tools to extract transmission line parameters. All design rules should be defined within such field‑solver tools.

9. For AC coupling capacitors on high‑speed signals, is it better to place them closer to the source or to the receiver?

There are different practices: some place them near the receiver, others near the driver. Let's first review the purpose of an AC coupling capacitor. Its main functions are threefold:

① The source and sink may have different DC levels, so the capacitor blocks DC.

② During transmission, DC offsets may be coupled in; the capacitor removes them, thus improving the signal eye diagram.

③ The AC coupling capacitor can also provide DC bias and over‑current protection.

In essence, the AC coupling capacitor provides DC bias, removes the DC component of the signal, and makes the signal symmetric about zero.

Why add it? It benefits communication between stages by improving noise margin. However, note that the AC coupling capacitor typically introduces an impedance discontinuity on high‑speed lines and can slow down signal edges.

Recommendations for placement:

  1. Some protocols or datasheets specify placement; follow those design guidelines.

  2. If no guideline is given, and it is an IC‑to‑IC connection, place the capacitor near the receiver.

  3. If it is an IC‑to‑connector connection, place it near the connector.

10. How can we verify that a PCB meets design and manufacturing requirements before it leaves the factory?

Many PCB manufacturers perform powered‑on continuity testing (netlist testing) before shipment to ensure all connections are correct. Additionally, more manufacturers now use X‑ray inspection to detect etching or lamination defects. For assembled boards after SMT, ICT (In‑Circuit Test) is typically used, which requires adding ICT test points during PCB design. If problems arise, special X‑ray inspection equipment can also help determine whether the failure was caused by the manufacturing process.

About Maxipcb

Maxipcb empowers innovators to turn cutting-edge technologies into reality.

We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.