Categories

A Brief Discussion on the Purpose of Test Points on PCBs

For anyone in electronics, it's second nature to place test points on a circuit board. How many people have never heard of test points? And how many know what they are for but don't really understand their purpose? Basically, test points are used to verify whether the components on a board meet specifications and to check solderability. For example, the simplest way to check if a resistor on a board is good is to measure its two ends with a multimeter.
Aug 8th,2026 109 Views

For anyone in electronics, it's second nature to place test points on a circuit board. How many people have never heard of test points? And how many know what they are for but don't really understand their purpose? Basically, test points are used to verify whether the components on a board meet specifications and to check solderability. For example, the simplest way to check if a resistor on a board is good is to measure its two ends with a multimeter.

However, in a high‑volume production factory, you can't afford to slowly measure every resistor, capacitor, inductor, or even IC on every board with a multimeter. That's why automated In‑Circuit‑Test (ICT) machines were developed. These machines use multiple probes (commonly referred to as a "Bed‑of‑Nails" fixture) to contact all the component leads that need to be tested simultaneously. Under program control, they measure the characteristics of these electronic components in a sequential (mainly serial, with some parallel) manner. Typically, testing all the components on an ordinary board takes about 1 to 2 minutes, depending on the number of components – more components mean longer test times.

But if these probes made direct contact with the electronic components or their solder joints on the board, they could easily crush some of the components, defeating the purpose. So clever engineers came up with the idea of "test points" – small circular pads added at the ends of each component, without solder mask, so that test probes can touch these pads instead of directly contacting the components themselves.

In the early days, when boards were populated with through‑hole (DIP) components, it was common to use the component leads themselves as test points, because those leads were sturdy enough to withstand probing. However, this often caused false failures due to poor probe contact. After wave soldering or SMT reflow, a thin film of flux residue typically forms on the solder surface, and that film has a very high impedance, which frequently leads to poor probe contact. At that time, it was common to see production test operators using air blow guns to blow vigorously at the boards, or wiping the test areas with alcohol. Even test points that went through wave soldering suffered from contact issues. Later, with the widespread adoption of SMT, false test failures were greatly reduced, and test points became much more important. Since SMT components are usually fragile and cannot withstand the direct pressure of test probes, using test points avoids direct contact with the components and their solder joints. This not only protects the components but also significantly improves test reliability, because false readings are much less frequent.

As technology has advanced, however, PCBs have become smaller and smaller, and squeezing all the electronic components onto a tiny board is already challenging. As a result, the space occupied by test points often becomes a tug‑of‑war between design and manufacturing. Test points are usually round, because the probes are also round – this makes them easier to produce and allows adjacent probes to be placed closer together, increasing the probing density of the bed‑of‑nails fixture. There are inherent mechanical limitations with bed‑of‑nails testing: for instance, there is a minimum diameter for probes – if the diameter is too small, the pins are prone to breaking. There is also a minimum pitch between probes, because each pin must emerge from a hole, and each pin must be soldered to a flat cable at its back end.

If adjacent holes are too small, not only is there a risk of short circuits between pins, but interference from the flat cables is also a major issue. Probes cannot be placed next to tall components – if a probe is too close, it may collide with and damage the component. Additionally, because tall components require cut‑outs in the test fixture, that also prevents probe placement. It is becoming increasingly difficult to accommodate test points for all components on today's dense boards. As boards continue to shrink, the necessity and number of test points are frequently debated. Several methods have emerged to reduce the need for test points, such as Net Test, Test Jet, Boundary Scan, JTAG, and others.

Other test methods, such as AOI (Automated Optical Inspection) and X‑Ray inspection, have also been proposed as alternatives to traditional bed‑of‑nails testing. However, none of these methods can yet replace ICT 100%. Regarding the probing capability for ICT, you should consult your fixture supplier for the minimum test‑point diameter and the minimum pitch between adjacent test points. Typically, there is a desired minimum and a minimum that the supplier can actually achieve. Reputable suppliers will also specify a maximum number of test points per unit area beyond which the fixture becomes susceptible to damage.

About Maxipcb

Maxipcb empowers innovators to turn cutting-edge technologies into reality.

We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.