Categories

Five Key Points in PCB Circuit Board Design!

The PCB circuit board is the fundamental electronic component underlying all electronic circuit designs, and PCB design is something that makers must understand. The role of a PCB is not just to combine scattered components, but also to ensure the regularity of circuit design, effectively avoiding the chaos and errors caused by manual wiring and connections.
Sep 7th,2026 63 Views

The PCB circuit board is the fundamental electronic component underlying all electronic circuit designs, and PCB design is something that makers must understand. The role of a PCB is not just to combine scattered components, but also to ensure the regularity of circuit design, effectively avoiding the chaos and errors caused by manual wiring and connections.


1. Have a Reasonable Routing Direction

Consider factors such as input/output, AC/DC, strong/weak signals, high/low frequency, and high/low voltage. Their routing directions should be linear (or separated) and should not intermingle. The purpose is to prevent mutual interference. The best routing direction is in a straight line, but this is generally difficult to achieve; the worst routing direction is a loop, but fortunately, isolation strips can be added to improve the situation. For DC, small‑signal, low‑voltage PCB designs, the requirements can be less stringent. Therefore, "reasonable" is a relative term.

2. Choose a Good Grounding Point – Often the Most Important Aspect

Countless engineers have written extensively about the humble grounding point, which shows just how important it is. In general, a single‑point ground is required – for example, the multiple ground traces of a preamplifier should be brought together before connecting to the main ground. In practice, due to various constraints, it is difficult to achieve this perfectly, but it should be followed as much as possible. This issue is actually quite flexible in practice; everyone has their own approach, and it is easier to understand if explained in the context of a specific circuit board.

3. Reasonably Place Power Supply Filtering/Decoupling Capacitors

In general, the schematic diagram only shows a number of power supply filtering/decoupling capacitors without indicating where each should be connected. In fact, these capacitors are intended for switching devices (gate circuits) or other components that require filtering/decoupling, so they should be placed as close as possible to those components. If placed too far away, they lose their effectiveness. Interestingly, when the power supply filtering/decoupling capacitors are placed reasonably, the grounding point issue becomes less obvious.

4. Trace Widths and Sizes, and Appropriate Via and Pad Dimensions

Traces that can be made wider should never be made narrower; high‑voltage and high‑frequency traces should be smooth, with no sharp corners, and right‑angle bends should be avoided. Ground traces should be as wide as possible, preferably using large copper‑pour areas, which significantly improves the grounding issue. Pads or via holes that are too small, or pad sizes that do not match the drilling sizes, can cause problems. The former is unfavourable for manual drilling, and the latter is unfavourable for CNC drilling. Small pads can easily be drilled into a "C" shape, or in severe cases, the pad may be completely drilled away. Traces that are too thin, combined with large un‑routed areas without copper pour, can lead to uneven etching. That is, after the un‑routed areas have been etched away, the thin traces may be over‑etched, becoming either intermittent or completely broken. Therefore, copper pouring is not only for increasing the ground area and improving noise immunity.

5. Number of Vias, Solder Joints, and Trace Density

Some issues are not easily discovered in the early stages of circuit fabrication; they often emerge later. For example, too many vias can lead to hidden problems if the copper‑plating process is not handled carefully. Therefore, the number of vias should be minimised in the design. When parallel traces are spaced too closely together, they can easily bridge during soldering. Therefore, the trace density should be determined based on the level of the soldering process. Solder joints that are too close together are not conducive to manual soldering, and the only way to maintain soldering quality is to reduce work efficiency. Otherwise, hidden risks remain. Therefore, the minimum distance between solder joints should be determined by considering both the skill level of the soldering personnel and the required efficiency.

If you can fully understand and master the above PCB circuit board design considerations, you will be able to significantly improve both design efficiency and product quality. Correcting errors during the fabrication process will save a great deal of time and cost, as well as reducing rework time and material investment.

About Maxipcb

Maxipcb empowers innovators to turn cutting-edge technologies into reality.We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.