Categories

Six Tips for Selecting PCB Components

Best PCB design practices: six things to consider when selecting PCB components based on component footprints. All examples in this article were developed using the Multisim design environment, but the same concepts apply even when using different EDA tools.
Sep 5th,2026 78 Views

Best PCB design practices: six things to consider when selecting PCB components based on component footprints. All examples in this article were developed using the Multisim design environment, but the same concepts apply even when using different EDA tools.


1. Consider Component Footprint Selection

Throughout the schematic capture phase, you should already be thinking about component footprint and pad pattern decisions that will need to be made during the layout phase. Below are some suggestions to consider when selecting components based on their footprints.

  • Remember that the footprint includes the electrical pad connections and the mechanical dimensions (X, Y, and Z) – that is, the physical outline of the component body and the pins that connect to the PCB. When selecting components, you need to consider any mounting or packaging constraints that may exist on the top and bottom layers of the final PCB. Some components (such as polarised capacitors) may have height‑clearance restrictions that should be taken into account during component selection. At the very beginning of the design, you can draw a basic board outline and place some of the large or critically positioned components (such as connectors) that you plan to use. This gives you a quick visual (un‑routed) 3D view of the board, showing relatively accurate placement and component heights. This helps ensure that, after assembly, the components will fit properly into the external enclosure (plastic case, chassis, frame, etc.). You can view the entire board in 3D preview mode from the Tools menu.

  • The pad pattern shows the actual pads or vias on the PCB where the component will be soldered. These copper patterns on the PCB also contain some basic shape information. Proper pad‑pattern dimensions are essential for correct soldering and to ensure the mechanical and thermal integrity of the connected component. When designing the PCB layout, you need to consider how the board will be manufactured, or if hand‑soldered, how the pads will be soldered. Reflow soldering (where the flux is melted in a controlled high‑temperature oven) can handle a wide variety of surface‑mount devices (SMDs). Wave soldering is generally used to solder the bottom side of the board to secure through‑hole components, but it can also handle some SMDs placed on the bottom side. When using this technique, bottom‑side SMDs usually must be oriented in a specific direction, and the pad patterns may need to be modified to accommodate this soldering method.

  • Component choices can change throughout the design process. Identifying early on which devices should be plated through‑hole (PTH) and which should be surface‑mount (SMT) helps with overall PCB planning. Factors to consider include component cost, availability, component density, and power dissipation. From a manufacturing perspective, SMT components are generally less expensive and more readily available than through‑hole components. For small to medium‑sized prototype projects, it is often better to choose larger SMT or through‑hole components, as they are easier to hand‑solder and allow better access to pads and signals for debugging and testing.

  • If an existing footprint is not available in the database, you typically create a custom footprint within the tool.


2. Use Good Grounding Practices

Make sure the design has adequate bypass capacitance and a ground plane. When using ICs, ensure that suitable decoupling capacitors are placed close to the power‑to‑ground connection (preferably to the ground plane). The appropriate capacitance value depends on the specific application, capacitor technology, and operating frequency. When bypass capacitors are placed between the power and ground pins and positioned close to the correct IC pins, they optimise the circuit's electromagnetic compatibility and susceptibility.


3. Assign Virtual Component Footprints

Print a bill of materials (BOM) to check for virtual components. Virtual components have no associated footprint and will not be transferred to the layout stage. Create a BOM and review all virtual components in the design. The only entries that should appear are power and ground signals, since they are treated as virtual components that are handled specially only in the schematic environment and are not passed to the layout. Unless they are used for simulation purposes, any components shown in the virtual section should be replaced with components that have real footprints.


4. Ensure Complete BOM Data

Check that the BOM report contains sufficiently complete data. After generating the BOM report, review it carefully and fill in any missing device, supplier, or manufacturer information for all component entries.


5. Sort by Reference Designator

To help with BOM sorting and viewing, ensure that component reference designators are numbered sequentially.


6. Check for Unused Gates

In general, all unused gate inputs should have signal connections to prevent floating inputs. Make sure to check for any unused or missing gates, and ensure that all unconnected inputs are fully terminated. In some cases, if an input is left floating, the entire system may not work correctly. Take, for example, the dual operational amplifier commonly used in designs. If only one of the two op‑amps in the dual package is used, it is recommended either to use the other op‑amp as well, or to ground the inputs of the unused op‑amp and provide an appropriate unity‑gain (or other gain) feedback network to ensure that the entire component functions properly.

In some cases, an IC with floating pins may not operate within its specified parameters. Typically, an IC will meet its specifications only when it – or the other gates within the same package – are not operating in saturation, i.e., when inputs or outputs are not near the supply rails. Simulation often does not catch this situation because simulation models generally do not couple the multiple sections of an IC together to model the effects of floating connections.

About Maxipcb

Maxipcb empowers innovators to turn cutting-edge technologies into reality.We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.