PCB, also known as Printed Circuit Board, realizes the circuit connection and function implementation between electronic components, and is also an important part of power circuit design. This article introduces the routing techniques for high-frequency circuits in PCB design.
PCB, also known as Printed Circuit Board, realizes the circuit connection and function implementation between electronic components, and is also an important part of power circuit design. This article introduces the routing techniques for high-frequency circuits in PCB design.
Multilayer Board Routing
High-frequency circuits often have high integration density and high routing density. Adopting multilayer boards is not only a necessity for routing but also an effective means to reduce interference. During the PCB Layout stage, reasonably selecting the size of the printed board with a certain number of layers can fully utilize the middle layers to set up shields, better achieve nearby grounding, effectively reduce parasitic inductance and shorten the signal transmission length, and also significantly reduce cross-interference between signals. All these methods are beneficial to the reliability of high-frequency circuits. With the same material, a 4-layer board has 20dB lower noise than a double-sided board. However, there is also a problem: the higher the number of PCB layers, the more complex the manufacturing process and the higher the unit cost. This requires that in PCB Layout, in addition to selecting a PCB board with an appropriate number of layers, reasonable component layout planning must be carried out and correct routing rules must be adopted to complete the design.
-
Minimize layer alternation of leads between pins of high-frequency circuit devices
The so-called "minimize layer alternation of leads" means that the fewer vias used in the component connection process, the better. A via can bring about a distributed capacitance of approximately 0.5pF. Reducing the number of vias can significantly increase speed and reduce the possibility of data errors.
-
Minimize the length of leads between pins of high-frequency circuit devices
The radiation intensity of a signal is proportional to the routing length of the signal line. The longer the high-frequency signal lead, the easier it is to couple to nearby components. Therefore, for high-frequency signal lines such as signal clocks, crystal oscillators, DDR data, LVDS lines, USB lines, and HDMI lines, the routing length is required to be as short as possible.
-
Minimize bending of leads between pins of high-speed electronic devices
The leads for high-frequency circuit routing are preferably full straight lines. If turning is required, 45-degree broken lines or arc turns can be used. This requirement is only used to improve the adhesion strength of copper foil in low-frequency circuits, but in high-frequency circuits, meeting this requirement can reduce the external emission and mutual coupling of high-frequency signals.
-
Pay attention to "crosstalk" introduced by close parallel routing of signal lines
High-frequency circuit routing requires attention to crosstalk introduced by close parallel routing of signal lines. Crosstalk refers to the coupling phenomenon between signal lines without direct connection. Since high-frequency signals are transmitted along transmission lines in the form of electromagnetic waves, the signal lines act as antennas, and the energy of the electromagnetic field is emitted around the transmission lines. The undesired noise signal generated by the mutual coupling of electromagnetic fields between signals is called crosstalk. The parameters of the PCB board layer, the spacing between signal lines, the electrical characteristics of the driving end and the receiving end, and the signal termination method all have a certain impact on crosstalk. Therefore, to reduce crosstalk of high-frequency signals, the following requirements should be met as much as possible during routing:
(1) If the routing space permits, insert a ground line or ground plane between two lines with severe crosstalk, which can play an isolation role and reduce crosstalk;
(2) When there is a time-varying electromagnetic field in the space around the signal lines and parallel distribution cannot be avoided, arrange a large area of "ground" on the opposite side of the parallel signal lines to significantly reduce interference;
(3) Under the premise of permitting routing space, increase the spacing between adjacent signal lines, reduce the parallel length of signal lines, and the clock line should be perpendicular to the key signal lines as much as possible rather than parallel;
(4) If parallel routing in the same layer is almost unavoidable, the routing directions in the two adjacent layers must be perpendicular to each other;
(5) In digital circuits, ordinary clock signals are signals with fast edge changes and have large external crosstalk. Therefore, in the design, the clock line should be surrounded by ground lines and more ground vias should be drilled to reduce distributed capacitance and thus reduce crosstalk;
(6) For high-frequency signal clocks, try to use low-voltage differential clock signals and ground wrapping methods, and pay attention to the integrity of ground wrapping and drilling;
(7) Unused input terminals should not be left floating, but should be grounded or connected to the power supply (the power supply is also ground in high-frequency signal loops), because a floating line may be equivalent to a transmitting antenna, and grounding can suppress emission. Practice has proved that using this method to eliminate crosstalk can sometimes take effect immediately.
-
Isolate the ground lines of high-frequency digital signals from analog signal ground lines
When analog ground lines, digital ground lines, etc. are connected to the common ground line, they should be connected with high-frequency choke beads or directly isolated and interconnected at a single point at a suitable location. The ground potentials of high-frequency digital signal ground lines are generally inconsistent, and there is often a certain voltage difference between the two when directly connected. Moreover, the ground lines of high-frequency digital signals are often very rich in harmonic components of high-frequency signals. When the digital signal ground line and the analog signal ground line are directly connected, the harmonics of the high-frequency signal will interfere with the analog signal through ground coupling. Therefore, in general, the ground lines of high-frequency digital signals and analog signal ground lines need to be isolated, which can be achieved by single-point interconnection at a suitable location or interconnection with high-frequency choke beads.
-
Add high-frequency decoupling capacitors to the power pins of integrated circuit blocks
Add a high-frequency decoupling capacitor near the power pin of each integrated circuit block. Adding high-frequency decoupling capacitors to power pins can effectively suppress the interference caused by high-frequency harmonics on the power pins.
-
Avoid loops formed by routing
All types of high-frequency signal routing should try not to form loops. If unavoidable, the loop area should be as small as possible.
-
Ensure good signal impedance matching
During signal transmission, when the impedance is mismatched, the signal will reflect in the transmission channel. Reflection will cause the composite signal to form overshoot, leading to signal fluctuations near the logic threshold.
The fundamental way to eliminate reflection is to make the impedance of the transmitted signal well matched. The greater the difference between the load impedance and the characteristic impedance of the transmission line, the greater the reflection. Therefore, the characteristic impedance of the signal transmission line should be made equal to the load impedance as much as possible. At the same time, attention should be paid to avoiding abrupt changes or corners in the transmission lines on the PCB, and keeping the impedance of each point of the transmission line continuous. Otherwise, reflection will also occur between each segment of the transmission line. This requires that the following routing rules must be followed in high-speed PCB routing:
(1) LVDS routing rules: Require differential routing for LVDS signals, with a line width of 7mil and a line spacing of 6mil, aiming to control the differential signal pair impedance of HDMI to 100±15% ohms;
(2) USB routing rules: Require differential routing for USB signals, with a line width of 10mil, a line spacing of 6mil, and a distance of 6mil between the ground line and the signal line;
(3) HDMI routing rules: Require differential routing for HDMI signals, with a line width of 10mil and a line spacing of 6mil, and the spacing between each two groups of HDMI differential signal pairs exceeds 20mil;
(4) DDR routing rules: DDR1 routing requires that signals do not pass through vias as much as possible, the signal lines are of equal width, the spacing between lines is equal, and the routing must meet the 2W principle to reduce crosstalk between signals. For high-speed devices such as DDR2 and above, it is also required that high-frequency data routing is of equal length to ensure signal impedance matching.
Maintain the integrity of signal transmission and prevent the "ground bounce phenomenon" caused by ground plane splitting.
About Maxipcb
Maxipcb empowers innovators to turn cutting-edge technologies into reality.
We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.