PCB layout design has always been a major challenge for PCB engineers, and RF circuit board design is even more difficult. Today, we will start by sharing some design experience for RF circuits.
The rapid development of RF integrated circuits has opened up broad prospects for engineering and technical personnel engaged in various wireless communications. If the grounding of an RF circuit is not handled properly, some strange phenomena may occur. For digital circuit design, even without a ground plane, most digital circuits still function well. However, in the RF frequency range, even a very short ground trace can act like an inductor. As a rough estimate, the inductance per millimetre of trace length is about 1 nH; at 433 MHz, the inductive reactance of a 10 mm PCB trace is approximately 27 Ω. Without a ground plane, most ground traces would be too long, and the circuit would not perform as designed. This illustrates the difficulty of RF circuit design.
Common Problems in RF Circuit Design
1. Interference between Digital and Analogue Circuit Modules
If analogue (RF) and digital circuits operate separately, each may work well. However, when placed on the same board and powered by the same supply, the entire system may become unstable. This is mainly because digital signals frequently swing between ground and the positive supply (>3 V), with very short periods, often in the nanosecond range. Due to the large amplitude and short switching times, these digital signals contain a significant amount of high‑frequency components independent of the switching frequency. In the analogue section, the signal received from the wireless tuning circuit to the receiver input is generally less than 1 μV. Thus, the difference between the digital signal and the RF signal can reach 120 dB. Clearly, if the digital and RF signals cannot be well separated, the weak RF signal may be corrupted, degrading the wireless device's performance or even rendering it completely inoperable.
2. Power Supply Noise Interference
RF circuits are quite sensitive to power supply noise, especially to voltage spikes and other high‑frequency harmonics. Microcontrollers draw a large current suddenly for a short period during each internal clock cycle, because modern microcontrollers are manufactured using CMOS technology. Therefore, if a microcontroller is running at an internal clock frequency of 1 MHz, it will draw current from the power supply at that frequency. Without proper power supply decoupling, voltage spikes will appear on the power line. If these voltage spikes reach the power pins of the RF section, they may cause malfunction in severe cases.
3. Radiated Interference from the Antenna to Other Analogue Circuits
In PCB design, boards typically contain other analogue circuits – for example, many boards have analogue‑to‑digital converters (ADCs) or digital‑to‑analogue converters (DACs). The high‑frequency signal from the RF transmitter's antenna may reach the analogue input of the ADC. Because any circuit trace can act like an antenna to transmit or receive RF signals, if the ADC input is not properly handled, the RF signal may cause oscillation within the ADC's input ESD diodes, resulting in ADC errors.
RF Circuit Design Principles and Solutions
1. RF Layout Concepts
When designing an RF layout, the following general principles must be prioritised:
Keep the high‑power RF amplifier (HPA) and the low‑noise amplifier (LNA) as far apart as possible – in simple terms, keep high‑power RF transmitting circuits away from low‑power RF receiving circuits.
Ensure that the high‑power area on the PCB has at least one solid ground plane, preferably with no vias in it – the larger the copper area, the better.
Circuit and power decoupling are also extremely important.
RF outputs should generally be kept away from RF inputs.
Sensitive analogue signals should be kept as far as possible from high‑speed digital signals and RF signals.
2. Physical and Electrical Partitioning Principles
Design partitioning can be broken down into physical partitioning and electrical partitioning. Physical partitioning mainly involves component placement, orientation, and shielding. Electrical partitioning can be further divided into power distribution, RF routing, sensitive circuit and signal partitioning, and grounding.
3. Physical Partitioning Principles
Component placement principles. Component placement is the key to achieving an excellent RF design. The most effective technique is to first place and orient the components that lie on the RF path, so that the RF path length is minimised and inputs are kept away from outputs. High‑power and low‑power circuits should be separated as far as possible.
PCB stackup design principles. The most effective stackup method is to place the main ground plane (main ground) on the second layer below the surface, and route RF traces on the surface layer wherever possible. Minimise the via sizes on the RF path – this not only reduces path inductance but also reduces solder voids on the main ground and limits the opportunity for RF energy to leak into other areas of the laminate.
RF device and RF routing layout principles. In physical space, linear circuits such as multi‑stage amplifiers are often sufficient to isolate multiple RF regions from each other, but duplexers, mixers, and IF amplifiers/mixers always have multiple RF/IF signals that interfere with each other. Therefore, this effect must be carefully minimised. RF and IF traces should cross each other as much as possible, and a ground area should be placed between them. The correct RF path is extremely important to the performance of the entire PCB – which is why component placement usually accounts for a large portion of the design time in cellular phone PCB designs.
Design principles for reducing coupling between high‑ and low‑power devices. On a cellular phone PCB, the LNA circuit can often be placed on one side of the PCB, while the HPA is placed on the other side, and they are ultimately connected on the same side to the RF terminal and the baseband processor antenna via a duplexer. Care must be taken to ensure that vias do not transfer RF energy from one side of the board to the other. A common technique is to use blind vias on both sides. The adverse effects of vias can be minimised by placing them in areas on both sides of the PCB that are not susceptible to RF interference.
RF circuit design requires designers to have practical experience and engineering design skills. The experience summarised in this article can help RF IC developers shorten development cycles, avoid unnecessary detours, and save both manpower and material resources.
As an important supporting element for electronic components and parts, the PCB circuit board plays a vital role in the electronics industry – it is often referred to as the "electronic aircraft carrier." With the advancement of science and technology, the application range of PCB circuit boards will become increasingly broad. To some extent, the level of PCB production technology has become an important indicator of a country's technological development.
About Maxipcb