Printed Circuit Boards (PCBs) are the core of every electronic device we use today. PCBs essentially interconnect electronic components by establishing conductive paths through copper pads and connecting traces. Therefore, the PCB assembly process has become one of the most fascinating concepts in electronics. This article introduces different types of PCB assembly processes and provides insights into their functionalities.
Printed Circuit Boards (PCBs) are the core of every electronic device we use today. PCBs essentially interconnect electronic components by establishing conductive paths through copper pads and connecting traces. Therefore, the PCB assembly process has become one of the most fascinating concepts in electronics. This article introduces different types of PCB assembly processes and provides insights into their functionalities.
Introduction to Traditional PCB Assembly Processes
The basic PCB assembly (commonly referred to as PCBA) proceeds as follows:
- Solder Paste Application: Solder paste particles mixed with flux are applied to the PCB substrate. Stencils of different sizes and shapes are used to ensure the paste is only deposited in specific locations.
- Component Placement: Small electronic components of the circuit are placed manually or automatically onto the solder pasted board using pick-and-place automated machinery.
- Reflow Soldering: The curing of the solder paste occurs during the reflow process. The PCB with mounted components is passed through a reflow oven at temperatures exceeding 500°F. After the solder paste melts, it is conveyed back and cured by exposure to a cooler environment.
- Inspection: This is performed after reflow soldering to verify component functionality. This stage is critical as it helps identify misaligned components, poor connections, and short circuits, which commonly occur during the reflow process. PCB manufacturers employ manual inspection, X-ray inspection, and automatic optical inspection (AOI) at this stage.
- Through-Hole Component Insertion: Many circuit boards require both through-hole and surface-mount components, which are inserted in this step. Through-hole insertion is typically performed using wave soldering or manual soldering.
- Final Inspection and Cleaning: Finally, the PCB board is tested for its electrical potential by applying different currents and voltages. Once the PCB passes this stage, it is cleaned with deionized water to remove residues left from soldering. After washing, it is dried under compressed air and packaged as a finished product.
This is the traditional PCB assembly process followed. As shown, most PCBs are assembled using Through-Hole Technology (THT), Surface Mount Technology (SMT), and hybrid assembly processes, which are discussed in further detail below.
Through-Hole Technology (THT) Assembly: Overview of Involved Steps
Only a few steps differ for THT-only PCBA. The steps for THT PCBA are as follows:
- Component Placement: In this process, components are manually installed by experienced engineers. The manual pick-and-place component installation process requires maximum precision and speed to ensure proper component placement. Engineers must follow THT standards and regulations to achieve optimal functionality.
- Inspection and Component Correction: The PCB board is aligned with the design transport frame to ensure accurate component placement. If any misplacement of components is found, corrections are made at this stage. Correction is easier before soldering, so component positions are adjusted during this phase.
- Wave Soldering: In THT, wave soldering is performed to cure the solder paste and secure components in their specific positions. During wave soldering, the PCB with mounted components moves over a slowly flowing stream of molten solder heated to temperatures above 500°F. It is then exposed to a cooler environment to solidify the connections.
Surface Mount Technology (SMT) Assembly: What Are the Different Steps Involved?
The PCBA steps followed in SMT assembly are as follows:
- Solder Paste Application/Printing: Solder paste is applied to the board using a solder paste printer with reference to the design stencil. This ensures the solder paste is printed in specific locations in satisfactory quantities.
- Component Placement: Component placement in SMT assembly is automated. The circuit board is sent from the printer to the component mounter, where components are picked and placed by automatic mechanical pick-and-place mechanisms. This technology saves time compared to manual processes and also ensures precision in specific component locations.
- Reflow Soldering: After component installation, the PCB is placed in an oven where the solder paste melts and deposits around the components. The PCB then passes through a cooler to secure the components in place.
Surface Mount Technology (SMT) is more efficient in complex PCB assembly processes.
Due to the increasing complexity of electronic devices and PCB designs, hybrid assembly types are also used in the industry. As the name suggests, the hybrid PCB assembly process is a combination of THT and SMT.
About Maxipcb
Maxipcb empowers innovators to turn cutting-edge technologies into reality.
We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.