Categories

A Brief Discussion on the Importance of PCB Electromagnetic Compatibility

What specifications should PCB design follow so that products meet electromagnetic compatibility (EMC) requirements?
Oct 31st,2026 24 Views

--------- Importance of PCB Electromagnetic Compatibility ---------

What specifications should PCB design follow so that products meet electromagnetic compatibility (EMC) requirements?

In the process of developing products, you may have encountered this: clearly a shielded enclosure is used, so why does the EMC test still fail? What is the reason for this?

Obviously, when the product was designed, only the EMC design of the enclosure was emphasized, while the EMC design of the PCB was ignored. Perhaps everyone has encountered some equipment whose enclosure has large gaps and openings, yet it passed the EMC test, which is somewhat hard to imagine. This shows that the EMC design of the PCB board/card is the core of product EMC design.

PCB EMC design is the most important part affecting product EMC testing.

--------- EMC Design Principles for PCB Boards ---------

Below are some EMC design experiences shared with you:

The design principle for product electromagnetic compatibility is that EMC design must be carried out during the new product R&D stage; otherwise, there may not even be a chance to remedy the situation later. EMC design is an important part of product development; it can greatly improve efficiency and save R&D costs to the maximum extent.

Experience tells us that carrying out EMC design simultaneously with functional design, and then passing the EMC test when the prototype board and prototype machine are completed, is the most time-saving and most cost-effective approach.

-- One of the key points of PCB EMC design: selection of components --

(1) For main components and integrated circuits, selection should mainly consider reducing radiated disturbance or improving RF radiation immunity. Try to choose chips with low emissions themselves, devices with low operating speed, and chips with multiple ground pins (a chip is essentially a circuit module with a high degree of integration; providing more ground pins during packaging can reduce the high-speed differential-mode current loop area S and correspondingly reduce the chip's emissions).

(2) Avoid using high-power and high-loss devices; they are often major radiation sources. Ensure that the selected devices do not operate in the nonlinear region, so as to avoid generating harmonic components that become interference sources.

(3) In addition to considering reducing radiated disturbance or improving RF radiation immunity, circuit design should also consider power supply circuit protection against external disturbances, including surge, electrical fast transient/burst, electrostatic discharge, voltage dip, voltage variation, etc.

(4) Circuit design or solutions should not cause overshoot in digital signal waveforms; they should minimize the amplitude of unwanted harmonic oscillations and minimize unwanted high-order harmonic components, avoiding strong electromagnetic interference.

(5) For lumped-parameter circuits, add damping and reduce the Q value to prevent oscillation.

-- The second key point of PCB EMC design: routing design --

(1) Minimize the loop area formed by all high-speed signal and clock signal lines. Connecting lines should be as short as possible, and signal lines should be adjacent to the ground return path.

(2) Use miniaturized devices and multilayer boards. Multilayer PCBs can compress routing space, have good high-frequency characteristics, and make it easy to achieve EMC.

(3) The selection of the number of PCB layers should consider the shielding and isolation requirements of critical signals. First determine the required number of signal layers, and then, under the premise of considering cost, adding ground planes and power planes is one of the best measures for PCB EMC design.

(4) The principle of PCB layer stacking is the same as the principle of arranging printed circuits and routing harnesses: the layer below the component side should be a ground plane; the critical power plane should be adjacent to its corresponding ground plane; critical signals on adjacent layers should not cross regions; all signal layers, especially high-speed signals and clock signals, should be adjacent to a ground plane; and adjacent signal layers should be avoided as much as possible.

(5) When an individual power plane or ground plane cannot serve as a continuous plane, use multi-via connections to form a ground grid/honeycomb mesh, which effectively reduces the current loop area, reduces the common impedance R, and increases the distributed capacitance between signals and the ground plane.

(6) When designing PCB routing, consider in the following order: power and ground / clock lines / signal lines. Routing should be short, straight, wide, and uniform; avoid right angles and abrupt changes; use zigzag routing where appropriate; use rounded corners instead of sharp traces; widen power and ground routing as much as possible; and make the partitioning of power and ground planes conform to microstrip and stripline requirements as much as possible.

(7) Route traces as far away as possible from disturbance sources. Consider the use of ferrite materials in routing, and reserve positions for ferrite beads and SMD filters so that they can be added or removed as needed.

-- The third key point of PCB EMC: grounding design --

(1) EMC design of high-speed signal lines and internal cables; PCB EMC design also mentions power supply and grounding, and EMC design of high-speed signal lines.

(2) Use low-impedance ground connections (ground planes) between chips. The impedance between the power supply pins of different chips should be as small as possible. Connect a high-frequency bypass capacitor between the chip power supply pin (meaning the power supply line very close to the chip power supply pin) and ground. Reserve positions for ferrite beads and SMD filters in the power supply routing so that they can be added or removed as needed.

(3) The core principle of routing and I/O harness arrangement is to reduce the current loop area S. The principle of arranging harnesses is the same as that of PCB layer stacking: critical power lines should be adjacent to their corresponding ground lines; all signal layers, especially high-speed signal and clock signal lines, should be adjacent to ground lines; and two signal lines should be adjacent to each other as little as possible.

(4) To avoid the ground wire being too long (approaching λ/4), multi-point local grounding can be used; the high-frequency impedance of the ground wire should be small.

(5) Reduce the antenna effect of cables and the dipole antenna effect. For cross wires and I/O harnesses, use cables with good shielding performance; use multi-strand twisted pairs for inner conductors so that spatial fields cancel each other; and the shielding layer can be used as the return line.

(6) Use shielded wires inside the machine to prevent induced noise.

(7) The input and output lines of the filter should be separated by a distance; avoid running them in parallel, so as not to affect the filtering effect.

(8) For I/O interfaces, pay attention to impedance matching of high-speed circuits to reduce and eliminate reflections.

About Maxipcb

Maxipcb empowers innovators to turn cutting-edge technologies into reality.We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.