Categories

Inventory of 70 High-Frequency PCB Circuit Design Issues

High-Frequency design and routing
Jun 30th,2026 89 Views

1. How to Select PCB Substrates?

PCB substrate selection must strike a balance between design requirements, manufacturability, and cost. Design requirements include both electrical and mechanical aspects. This material issue becomes particularly critical when designing very high-speed PCB boards (frequencies above GHz).
For example, the commonly used FR-4 material exhibits significant dielectric loss at several GHz frequencies, leading to substantial signal attenuation and making it unsuitable for such applications. From an electrical perspective, attention must be paid to whether the dielectric constant and dielectric loss are appropriate for the designed operating frequency.

2. How to Avoid High-Frequency Interference?

The basic idea for avoiding high-frequency interference is to minimize the electromagnetic field interference of high-frequency signals, commonly known as crosstalk. This can be achieved by increasing the distance between high-speed signals and analog signals, or adding ground guard/shunt traces next to analog signals. Attention must also be paid to the noise interference of digital ground on analog ground.

3. How to Solve Signal Integrity Issues in High-Speed Design?

Signal integrity is essentially a matter of impedance matching. Factors affecting impedance matching include the signal source architecture and output impedance, the characteristic impedance of the trace, the characteristic impedance of the load end, and the topology of the trace. The solutions are termination and adjustment of the trace topology.

4. How is Differential Routing Implemented?

There are two key points for differential pair routing: first, the lengths of the two lines should be as equal as possible; second, the spacing between the two lines (determined by the differential impedance) must remain constant, i.e., they must remain parallel. There are two parallel implementation methods: one is routing the two lines on the same layer (side-by-side), and the other is routing them on two adjacent upper and lower layers (over-under). Generally, the side-by-side method is more commonly used.

5. How to Implement Differential Routing for a Clock Signal Line with Only One Output?

Differential routing is only meaningful if both the signal source and the receiving end are differential signals. Therefore, differential routing cannot be used for a clock signal with only one output.

6. Can a Matching Resistor Be Added Between the Differential Line Pairs at the Receiving End?

A matching resistor is usually added between the differential line pairs at the receiving end, with its value equal to the differential impedance. This improves signal quality.

7. Why Should Differential Pairs Be Routed Close and Parallel?

Differential pairs should be routed appropriately close and parallel. The term "appropriately close" means that the spacing affects the differential impedance value, which is a critical parameter for differential pair design. Parallel routing is required to maintain consistent differential impedance. If the two lines are alternately close and far, the differential impedance will be inconsistent, affecting signal integrity and timing delay.

8. How to Handle Theoretical Conflicts in Actual Routing?

Basically, separating and isolating analog and digital grounds is correct. It is important to ensure that signal traces do not cross the split area (moat), and that the return current paths for power and signals are not excessively large.
Crystal oscillators are analog positive feedback oscillation circuits that require stable loop gain and phase specifications to generate a stable oscillation signal. These analog oscillation specifications are highly susceptible to interference, and even adding ground guard traces may not provide complete isolation. Furthermore, excessive distance will allow noise on the ground plane to affect the positive feedback oscillation circuit. Therefore, the crystal oscillator must be placed as close as possible to the chip.
Indeed, there are many conflicts between high-speed routing and EMI requirements. However, the basic principle is that resistors, capacitors, or ferrite beads added for EMI must not cause the signal's electrical characteristics to violate specifications. Therefore, it is best to first solve or reduce EMI problems through routing and PCB stack-up techniques, such as routing high-speed signals on inner layers. Only as a last resort should resistors, capacitors, or ferrite beads be used to minimize damage to the signal.

9. How to Resolve the Conflict Between Manual and Automatic Routing for High-Speed Signals?

Most automatic routers in advanced routing software now allow setting constraints to control routing methods and the number of vias. The routing engine capabilities and constraint setting options of different EDA companies sometimes vary significantly.
For example, whether there are sufficient constraints to control the winding pattern of serpentine lines, or to control the routing spacing of differential pairs, will affect whether the automatically routed traces meet the designer's expectations.
In addition, the difficulty of manual routing adjustment is absolutely related to the routing engine's capabilities, such as the ability to push traces, push vias, and even push traces against copper pours. Therefore, selecting a routing engine with strong capabilities is the solution.

10. About Test Coupons

Test coupons are used with a Time Domain Reflectometer (TDR) to measure whether the characteristic impedance of the manufactured PCB meets the design requirements. Generally, the impedances to be controlled include single-ended lines and differential pairs.
Therefore, the trace width and spacing (for differential pairs) on the test coupon must be identical to those of the lines to be controlled. Most importantly, the location of the ground point during measurement is critical.
To reduce the inductance of the ground lead, the TDR probe ground is usually placed very close to the signal measurement point (probe tip). Therefore, the distance and method between the signal measurement point and the ground point on the test coupon must match the probe being used.

11. In High-Speed PCB Design, Copper Can Be Poured in Blank Areas of Signal Layers. How Should Copper Pouring Be Allocated Between Ground and Power Across Multiple Signal Layers?

In most cases, copper pouring in blank areas is for grounding. However, when pouring copper next to high-speed signal lines, attention must be paid to the distance between the copper and the signal line, as the poured copper will slightly reduce the characteristic impedance of the trace. Care must also be taken not to affect the characteristic impedance of other layers, such as in a dual stripline structure.

12. Can the Microstrip Line Model Be Used to Calculate the Characteristic Impedance of Signal Lines on the Power Plane? Can the Stripline Model Be Used for Signals Between the Power and Ground Planes?

Yes. When calculating characteristic impedance, both the power plane and ground plane must be considered as reference planes. For example, in a 4-layer board: Top Layer - Power Plane - Ground Plane - Bottom Layer, the characteristic impedance of the top layer traces is calculated using the microstrip line model with the power plane as the reference plane.

13. Can Test Points Automatically Generated by Software on High-Density PCBs Generally Meet the Testing Requirements for Mass Production?

Whether automatically generated test points meet testing requirements depends on whether the specifications for adding test points comply with the requirements of the testing equipment. Additionally, if the traces are too dense and the test point specifications are strict, it may be impossible to automatically add test points to every trace segment, requiring manual completion of the remaining test points.

14. Will Adding Test Points Affect the Quality of High-Speed Signals?

Whether test points affect signal quality depends on how they are added and the signal speed. Basically, external test points (not using existing vias or DIP pins on the line) may be added directly to the line or as a short stub branching off the line.
The former is equivalent to adding a very small capacitor to the line, while the latter adds a branch. Both conditions will have some impact on high-speed signals, with the degree of impact related to the signal frequency and edge rate. The magnitude of the impact can be determined through simulation. In principle, smaller test points (while still meeting testing equipment requirements) and shorter stubs are better.

15. How Should Ground Wires Be Connected Between Multiple PCBs in a System?

When signals or power are transferred between interconnected PCBs—for example, when board A sends power or a signal to board B—an equal amount of current will flow back from the ground plane to board A (Kirchhoff's Current Law).
This current on the ground plane will find the path of least impedance. Therefore, the number of pins allocated to the ground plane at each interface where power or signals are interconnected must not be too small, to reduce impedance and thus minimize noise on the ground plane.
Additionally, the entire current loop, especially for high-current sections, can be analyzed to adjust the ground plane or ground wire connections to control the current path (e.g., creating a low-impedance path at a specific location to direct most of the current there) and reduce interference with more sensitive signals.

16. Can You Recommend Some Foreign Technical Books and Data on High-Speed PCB Design?

High-speed digital circuit applications currently include fields such as communication networks and computers. In communication networks, PCB operating frequencies have reached GHz levels, and stack-up layers can be as high as 40 layers to my knowledge.
In computer-related applications, advances in chips have pushed the maximum operating frequency on boards to over 400 MHz (e.g., Rambus) for both general PCs and servers.
In response to these high-speed, high-density routing requirements, demand for blind/buried vias, microvias, and build-up processes is increasing. These design requirements are now mass-producible by various manufacturers.

17. Two Commonly Referenced Characteristic Impedance Formulas

  • Microstrip Line:
    Z = {87/[sqrt(Er+1.41)]} × ln[5.98H/(0.8W+T)]
    Where: W = trace width, T = copper thickness of the trace, H = distance from the trace to the reference plane, Er = dielectric constant of the PCB material.
    This formula is valid for 0.1 < (W/H) < 2.0 and 1 < Er < 15.
  • Stripline:
    Z = [60/sqrt(Er)] × ln{4H/[0.67π(T+0.8W)]}
    Where: H = distance between the two reference planes, with the trace located midway between them.
    This formula is valid for W/H < 0.35 and T/H < 0.25.

18. Can a Ground Wire Be Added Between Differential Signal Lines?

Generally, a ground wire cannot be added between differential signals. The most important principle of differential signal applications is to leverage the benefits of mutual coupling between differential signals, such as flux cancellation and noise immunity. Adding a ground wire in the middle will destroy this coupling effect.

19. Does Rigid-Flex Board Design Require Specialized Design Software and Specifications? Where in China Can Such Circuit Board Processing Be Undertaken?

General PCB design software can be used to design flexible printed circuits (FPC). Gerber format is still provided to FPC manufacturers for production. Due to differences in manufacturing processes compared to standard PCBs, each manufacturer will specify their own minimum trace width, minimum trace spacing, and minimum via diameter based on their capabilities.
Additionally, copper can be poured at the bends of flexible circuits for reinforcement. Manufacturers can be found by searching for "FPC" online.

20. What Are the Principles for Selecting Appropriate Grounding Points Between the PCB and the Enclosure?

The principle for selecting PCB-to-enclosure grounding points is to use chassis ground to provide a low-impedance path for return currents and control the return current path.
For example, near high-frequency devices or clock generators, the PCB ground plane can be connected to chassis ground using mounting screws to minimize the entire current loop area and thus reduce electromagnetic radiation.

21. From Which Aspects Should Circuit Board DEBUG Be Approached?

For digital circuits, first confirm three things in sequence:
  1. Verify that all power supply voltages meet design requirements. Some multi-power systems may have specific requirements for the sequence and speed of power-up.
  2. Confirm that all clock signals are operating at the correct frequency and that there are no non-monotonic issues on the signal edges.
  3. Confirm that the reset signal meets specification requirements.
If these are normal, the chip should generate the first cycle of signals. Subsequent debugging follows the system operating principles and bus protocol.

22. In High-Speed (>100MHz) High-Density PCB Design, How to Improve Performance When Increasing Routing Density Leads to Enhanced Interference and Inability to Reduce Impedance Due to Narrow Traces?

In high-speed high-density PCB design, crosstalk interference is indeed a critical concern, as it significantly impacts timing and signal integrity. The following key points are provided:
  1. Control the continuity and matching of trace characteristic impedance.
  2. Pay attention to trace spacing. A common spacing is twice the trace width. Simulation can be used to determine the minimum tolerable spacing for timing and signal integrity, as results may vary for different chip signals.
  3. Select appropriate termination methods.
  4. Avoid routing in the same direction on adjacent upper and lower layers, especially overlapping traces, as this causes more severe crosstalk than adjacent traces on the same layer.
  5. Use blind/buried vias to increase routing area, though this increases PCB manufacturing costs.
While it is difficult to achieve perfect parallelism and equal length in practice, every effort should be made. Additionally, differential and common-mode terminations can be reserved to mitigate impacts on timing and signal integrity.

23. LC Circuits Are Often Used for Filtering at Analog Power Supplies. Why Is LC Filtering Sometimes Less Effective Than RC Filtering?

The comparison of LC and RC filtering effectiveness depends on whether the frequency band to be filtered and the selected inductance value are appropriate. The inductive reactance is related to both the inductance value and frequency. If the power supply noise frequency is low and the inductance value is insufficient, the filtering effect may be inferior to RC filtering.
However, the tradeoff for using RC filtering is that the resistor itself dissipates power, resulting in lower efficiency, and care must be taken to ensure the selected resistor can handle the power.

24. What Is the Method for Selecting Inductor and Capacitor Values for Filtering?

Inductor value selection must consider both the noise frequency to be filtered and the instantaneous current response capability. If the LC output may need to supply large instantaneous currents, an excessively large inductor will impede the flow of this large current, increasing ripple noise.
Capacitor value selection is related to the acceptable ripple noise specification. Smaller allowable ripple noise requires larger capacitor values. The ESR/ESL of the capacitor also has an impact.
Additionally, if the LC is placed at the output of a switching regulator, attention must be paid to the effect of the pole-zero generated by the LC on the stability of the negative feedback control loop.

25. How to Meet EMC Requirements Without Excessive Cost Pressure?

The increased cost of PCBs due to EMC typically comes from adding ground layers to enhance shielding and adding components such as ferrite beads and chokes to suppress high-frequency harmonics.
In addition, other mechanical shielding structures are usually required to make the entire system pass EMC requirements. The following PCB design techniques are provided to reduce electromagnetic radiation from circuits:
  • Use devices with slower signal slew rates to reduce high-frequency components generated by the signal.
  • Pay attention to the placement of high-frequency devices, keeping them away from external connectors.
  • Focus on high-speed signal impedance matching, trace layers, and return current paths to reduce high-frequency reflections and radiation.
  • Place sufficient and appropriate decoupling capacitors at the power pins of each device to mitigate noise on the power and ground planes. Special attention must be paid to whether the capacitor's frequency response and temperature characteristics meet design requirements.
  • The ground near external connectors can be appropriately separated from the ground plane, and the connector ground can be connected nearby to chassis ground.
  • Appropriately use ground guard/shunt traces next to particularly high-speed signals, but note their impact on trace characteristic impedance.
  • Retract the power plane by 20H relative to the ground plane, where H is the distance between the power and ground planes.

26. When a PCB Contains Multiple Digital/Analog Functional Blocks, the Conventional Practice Is to Separate Digital and Analog Grounds. Why?

The reason for separating digital and analog grounds is that digital circuits generate noise on the power and ground when switching between high and low potentials. The magnitude of this noise is related to the signal speed and current magnitude.
If the ground plane is not split and the noise generated by the digital area circuits is large while the analog area circuits are very close, the analog signals will still be interfered with by ground noise even if the digital and analog signals do not cross. In other words, the unsplit ground approach is only applicable when the analog circuit area is far from the digital circuit area generating large noise.

27. Another Approach Is to Ensure Separate Digital/Analog Layout and No Crossing of Digital/Analog Signal Traces, While Keeping the Entire PCB Ground Unsplitted and Connecting Both Digital and Analog Grounds to This Plane. What Is the Rationale?

The requirement for no crossing of digital and analog signal traces is because the return current path of faster digital signals will flow back to the digital signal source along the ground directly below the trace. If digital and analog signal traces cross, the noise generated by the return current will appear in the analog circuit area.

28. How to Consider Impedance Matching During Schematic Design for High-Speed PCB Circuits?

Impedance matching is one of the key elements in high-speed PCB circuit design. The impedance value is absolutely related to the routing method—for example, whether the trace is on the surface layer (microstrip) or inner layer (stripline/double stripline), the distance to the reference layer (power or ground plane), trace width, and PCB material all affect the characteristic impedance of the trace.
In other words, the impedance value can only be determined after routing. Generally, simulation software cannot account for some impedance discontinuities in routing due to limitations in circuit models or mathematical algorithms. Therefore, only terminators such as series resistors can be reserved on the schematic to mitigate the effects of impedance discontinuities. The fundamental solution is to carefully avoid impedance discontinuities during routing.

29. Where Can Accurate IBIS Model Libraries Be Obtained?

The accuracy of IBIS models directly affects simulation results. Essentially, IBIS can be viewed as electrical characteristic data for the equivalent circuit of an actual chip's I/O buffer, generally converted from SPICE models. Since SPICE data is absolutely related to chip manufacturing, the SPICE data provided by different chip manufacturers for the same device will differ, and thus the data in the converted IBIS models will also vary.
In other words, if you use a device from Manufacturer A, only they have the ability to provide accurate model data for their device, as no one else knows their manufacturing process better. If the IBIS provided by the manufacturer is inaccurate, the only fundamental solution is to continuously request improvements from the manufacturer.

30. What EMC/EMI Rules Should Designers Consider During High-Speed PCB Design?

General EMI/EMC design must consider both radiated and conducted emissions. The former relates to higher frequencies (>30MHz), while the latter to lower frequencies (<30MHz). Therefore, attention must be paid to both high and low frequencies, not just high frequencies.
A good EMI/EMC design must consider device placement, PCB stack-up, critical trace routing, and component selection from the very beginning of layout. If these are not properly planned in advance, post-hoc solutions will be half as effective and twice as costly.
For example, the clock generator should be placed as far as possible from external connectors; high-speed signals should be routed on inner layers with attention to characteristic impedance matching and reference plane continuity to reduce reflections; the signal slew rate pushed by devices should be as small as possible to reduce high-frequency components; and decoupling/bypass capacitors should be selected with appropriate frequency response to reduce power plane noise.
Additionally, the return path of high-frequency signal currents should be controlled to minimize the loop area (i.e., minimize loop impedance) to reduce radiation. Split ground planes can also be used to control the range of high-frequency noise. Finally, select appropriate PCB-to-enclosure grounding points (chassis ground).

31. How to Select EDA Tools?

Among current PCB design software, thermal analysis is not a strong point, so it is not recommended for this purpose. For other functions, PADS or Cadence offer good performance and cost-effectiveness.
Beginners in PLD design can use the integrated environment provided by PLD chip manufacturers. For designs exceeding one million gates, single-point tools can be selected.

32. Please Recommend an EDA Software Suitable for High-Speed Signal Processing and Transmission.

For conventional circuit design, INNOVEDA's PADS is excellent and comes with matching simulation software, covering approximately 70% of application scenarios.
For high-speed circuit design and mixed analog-digital circuits, Cadence's solutions offer good performance and cost-effectiveness. Mentor's products are also very good, particularly in design process management.

33. Explanation of the Meaning of Each PCB Layer

  • Top Overlay: Top-layer component names, also called top silkscreen or top component legend, e.g., R1, C5, IC10.
  • Bottom Overlay: Same as above, for the bottom layer.
  • Multilayer: If you design a 4-layer board and place a free pad or via defined as multilayer, the pad will automatically appear on all 4 layers. If you define it only as the top layer, the pad will only appear on the top layer.

34. What Key Aspects Should Be Focused on for Routing and Layout in High-Frequency PCB Design Above 2GHz?

High-frequency PCB design above 2GHz belongs to radio frequency (RF) circuit design, which is outside the scope of high-speed digital circuit design. RF circuit layout and routing should be considered together with the schematic, as both layout and routing introduce distributed effects.
Furthermore, some passive components in RF circuit design are implemented through parameterized definitions and specially shaped copper foils. Therefore, EDA tools must provide parameterized components and the ability to edit specially shaped copper foils. Mentor's BoardStation includes a dedicated RF design module that meets these requirements. Additionally, RF design generally requires specialized RF circuit analysis tools, with Agilent's EESoft being the most famous in the industry and having excellent interfaces with Mentor's tools.

35. What Rules Should Be Followed for Microstrip Design in High-Frequency PCB Design Above 2GHz?

RF microstrip line design requires 3D field analysis tools to extract transmission line parameters. All rules should be specified within this field extraction tool.

36. For an All-Digital Signal PCB with an 80MHz Clock Source, Besides Using a Grounded Silk Screen, What Circuit Protection Should Be Used to Ensure Sufficient Driving Capability?

Ensuring clock driving capability should not be achieved through protection; clock driver chips are generally used. Concerns about clock driving capability usually arise from multiple clock loads. A clock driver chip converts one clock signal into several, using point-to-point connections.
When selecting a driver chip, in addition to ensuring basic matching with the load and meeting signal edge requirements (clocks are generally edge-active signals), the delay within the driver chip must be included in system timing calculations.

37. If a Separate Clock Signal Board Is Used, What Interface Should Be Adopted to Ensure Minimal Impact on Clock Signal Transmission?

Shorter clock signals result in smaller transmission line effects. Using a separate clock signal board increases signal routing length and introduces issues with single-board grounding and power supply. For long-distance transmission, differential signals are recommended. LVDS signals can meet driving capability requirements, though they are unnecessary for slower clocks.

38. The 27M and SDRAM clock lines (80M-90M) have second and third harmonics exactly in the VHF band, causing significant interference when coupled in from the receiving end. Besides shortening the line length, what other effective methods are there?

If the third harmonic is large and the second harmonic is small, it may be due to a 50% signal duty cycle, as this condition results in no even harmonics. In this case, modifying the signal duty cycle can help. Additionally, for unidirectional clock signals, source series matching is generally used.
This suppresses secondary reflections without affecting the clock edge rate. The source matching value can be obtained using the formula shown in the figure below.

39. What Is Trace Topology?

Topology, also called routing order, refers to the routing sequence for networks with multi-port connections.

40. How to Adjust Trace Topology to Improve Signal Integrity?

Network signal directions are complex, as topology affects signal quality differently for unidirectional, bidirectional, and different level signals. It is difficult to say which topology is universally beneficial for signal quality. Moreover, pre-simulation requires engineers to have a deep understanding of circuit principles, signal types, and even routing difficulty to select the appropriate topology.

41. How to Reduce EMI Problems Through Stack-Up Arrangement?

First, EMI must be considered at the system level; PCBs alone cannot solve the problem. For EMI, stack-up primarily provides the shortest signal return path, reduces coupling area, and suppresses differential-mode interference. Additionally, tight coupling between the ground and power planes, with the ground plane appropriately extending beyond the power plane, helps suppress common-mode interference.

42. Why Pour Copper?

Copper pouring is generally done for several reasons:
  1. EMC: Large-area ground or power copper pours provide shielding, with special grounds such as PGND serving protective functions.
  2. PCB Process Requirements: To ensure plating effectiveness or prevent warpage during lamination, copper is poured on PCB layers with sparse routing.
  3. Signal Integrity Requirements: To provide a complete return path for high-speed digital signals and reduce routing for DC networks.
    Other reasons include heat dissipation and special device installation requirements.

43. What Should Be Noted When Routing a System Containing DSP and PLD?

It depends on the ratio of signal propagation delay on the transmission line to the signal edge transition time. If the delay is comparable to the edge time, signal integrity issues must be considered.
Additionally, for multiple DSPs, the routing topology of clock and data signals will also affect signal quality and timing, requiring attention.

44. Are There Other Good Routing Tools Besides Protel?

Besides Protel, there are many routing tools, such as Mentor's WG2000, EN2000 series and PowerPCB, Cadence's Allegro, and Zuken's Cadstar and CR5000, each with their own strengths.

45. What Is a "Signal Return Path"?

The signal return path, or return current, refers to the path taken by high-speed digital signals during transmission: the signal flows from the driver along the PCB transmission line to the load, then returns from the load to the driver via the shortest path through ground or power.
This return signal on ground or power is called the signal return path. Dr. Johnson explains in his book that high-frequency signal transmission is actually the process of charging the dielectric capacitance sandwiched between the transmission line and the DC plane. SI analysis examines the electromagnetic characteristics of this surrounding field and their coupling.

46. How to Perform SI Analysis on Connectors?

The IBIS 3.2 specification includes descriptions of connector models, generally using EBD models. For special boards such as backplanes, SPICE models are required.
Multi-board simulation software (HYPERLYNX or IS_multiboard) can also be used. When building a multi-board system, input the distributed parameters of the connector, generally obtained from the connector datasheet. While this method may not be perfectly accurate, it is acceptable within tolerable limits.

47. What Are the Termination Methods?

Termination, also known as matching, is generally divided into source termination and load termination based on location. Source termination is typically series resistor matching, while load termination is generally parallel matching with various methods including resistor pull-up, resistor pull-down, Thevenin matching, AC matching, and Schottky diode matching.

48. What Factors Determine the Termination (Matching) Method Used?

The matching method is generally determined by the buffer characteristics, topology, signal level types, and decision methods, as well as signal duty cycle and system power consumption.

49. What Rules Apply to Termination (Matching) Methods?

The most critical aspect of digital circuits is timing. The purpose of adding matching is to improve signal quality and obtain a determinable signal at the decision time. For level-active signals, signal quality must be stable while meeting setup and hold time requirements; for edge-active signals, signal edge monotonicity must be maintained and the edge rate must meet requirements.
Mentor's ICX product materials include information on matching. Additionally, High Speed Digital Design: A Handbook of Black Magic has a dedicated chapter on termination, explaining the role of matching in signal integrity from electromagnetic wave principles, which is recommended for reference.

50. Can IBIS Models Be Used to Simulate the Logical Functions of Devices? If Not, How to Perform Board-Level and System-Level Simulation of Circuits?

IBIS models are behavioral models and cannot be used for functional simulation. Functional simulation requires SPICE models or other structural-level models.

51. In Mixed Digital-Analog Systems, There Are Two Processing Methods: 1) Separate Digital and Analog Grounds, Connected at a Single Point with Copper Foil or FB Ferrite Beads, with Power Unsplitted; 2) Separate Analog and Digital Power Supplies Connected with FB, with a Unified Ground. Are These Two Methods Equally Effective?

In principle, they are equivalent. Because power and ground are equivalent for high-frequency signals.
The purpose of separating analog and digital sections is for anti-interference, primarily to prevent digital circuits from interfering with analog circuits. However, splitting may result in incomplete signal return paths, affecting the signal quality of digital signals and reducing system EMC performance.
Therefore, regardless of which plane is split, it is necessary to consider whether the signal return path is enlarged and how much the return signal interferes with normal operating signals. Some mixed designs now do not split power or ground, but instead layout and route digital and analog sections separately to avoid cross-region signals.

52. Safety Compliance Issues: What Are the Specific Meanings of FCC and EMC?

  • FCC: Federal Communications Commission (United States)
  • EMC: Electromagnetic Compatibility
FCC is a standards organization, and EMC is a standard. All standards are issued with corresponding rationales, specifications, and test methods.

53. What Is Differential Routing?

Differential signals, also called differential signals, transmit a single data stream using two identical, opposite-polarity signals, with decisions based on the voltage difference between the two signals. To ensure the two signals are perfectly matched, they must be routed in parallel with constant line width and spacing.

54. What PCB Simulation Software Is Available?

There are many types of simulation. For high-speed digital circuit signal integrity (SI) analysis, commonly used software includes ICX, SignalVision, HyperLynx, XTK, and SpectraQuest. Some also use Hspice.

55. How Does PCB Simulation Software Perform Layout Simulation?

In high-speed digital circuits, to improve signal quality and reduce routing difficulty, multilayer boards are generally used with dedicated power and ground planes.

56. How to Ensure the Stability of Signals Above 50MHz During Layout and Routing?

The key to high-speed digital signal routing is to minimize the impact of transmission lines on signal quality. Therefore, high-speed signals above 100MHz require the shortest possible trace lengths. In digital circuits, high-speed signals are defined by their rise time.
Furthermore, different signal types (e.g., TTL, GTL, LVTTL) require different methods to ensure signal quality.

57. The RF Section, IF Section, and Even the Low-Frequency Monitoring Circuitry of Outdoor Units Are Often Deployed on the Same PCB. What Are the Material Requirements for Such PCBs? How to Prevent Mutual Interference Between RF, IF, and Low-Frequency Circuits?

Mixed circuit design is a significant challenge, and there is no perfect solution.
Generally, RF circuits are laid out and routed as independent single boards in the system, often with dedicated shielding cavities. RF circuits are typically single or double-sided boards with simple circuitry, all designed to minimize the impact of distributed parameters on RF circuits and improve RF system consistency.
Compared to standard FR-4 materials, RF circuit boards tend to use high-Q substrates with lower dielectric constants, smaller distributed capacitance of transmission lines, higher impedance, and smaller signal propagation delay. In mixed circuit design, although RF and digital circuits are on the same PCB, they are generally divided into separate RF and digital circuit areas with separate layout and routing, shielded by grounded via arrays and shielding boxes.

58. What Solutions Does Mentor Offer for Deploying RF, IF, and Low-Frequency Circuits on the Same PCB?

Mentor's board-level system design software includes dedicated RF design modules in addition to basic circuit design functions.
The RF schematic design module provides parameterized component models and bidirectional interfaces with RF circuit analysis and simulation tools such as EESoft. The RF layout module provides specialized pattern editing functions for RF circuit layout and routing, also with bidirectional interfaces to EESoft. Simulation results can be back-annotated to the schematic and PCB.
Additionally, Mentor's design management capabilities enable easy design reuse, design derivation, and collaborative design, significantly accelerating the mixed circuit design process. Mobile phone boards are typical mixed circuit designs, and many large mobile phone design manufacturers use Mentor plus Agilent's EESoft as their design platform.

59. What Is Mentor's Product Structure?

Mentor Graphics' PCB tools include the WG (formerly Veribest) series and the Enterprise (BoardStation) series.

60. How Does Mentor's PCB Design Software Support Packages Such as BGA, PGA, and COB?

Mentor's AutoActive RE, developed from the acquired Veribest, is the industry's first gridless, arbitrary-angle router. As is well known, gridless, arbitrary-angle routers are critical for achieving high routing completion rates for ball grid arrays (BGA) and chip-on-board (COB) devices.
The latest AutoActive RE adds features such as via pushing, copper foil pushing, and REROUTE, making it more versatile. It also supports high-speed routing, including timing-constrained signal routing and differential pair routing.

61. How Does Mentor's PCB Design Software Handle Differential Pairs?

After defining differential pair attributes in Mentor software, the two differential pairs can be routed together, strictly maintaining line width, spacing, and length difference. They automatically separate when encountering obstacles, and via placement methods can be selected when changing layers.

62. On a 12-Layer PCB with Three Power Planes (2.2V, 3.3V, 5V), How Should the Ground Plane Be Handled?

Generally, placing the three power supplies on separate layers provides better signal quality, as it minimizes the possibility of signal cross-plane splits. Cross-splitting is a critical factor affecting signal quality, and simulation software generally ignores it.
For high-frequency signals, power and ground planes are equivalent. In practice, in addition to signal quality, power plane coupling (using adjacent ground planes to reduce the AC impedance of the power plane) and stack-up symmetry must also be considered.

63. How Are PCBs Inspected for Compliance with Design Process Requirements Before Shipment?

Many PCB manufacturers perform powered network continuity tests after PCB processing to ensure all connections are correct. Additionally, an increasing number of manufacturers use X-ray testing to inspect for defects during etching or lamination.
For finished boards after SMT assembly, ICT (In-Circuit Test) is generally used, which requires adding ICT test points during PCB design. If problems occur, a special X-ray inspection device can be used to rule out manufacturing defects.

64. Is "Mechanical Protection" the Same as Enclosure Protection?

Yes. The enclosure should be as tightly sealed as possible, use minimal or no conductive materials, and be grounded as much as possible.

65. Should the Chip's Own ESD Characteristics Be Considered During Chip Selection?

Whether using double-sided or multilayer boards, the ground area should be maximized. When selecting chips, their inherent ESD characteristics must be considered, which are generally mentioned in the chip datasheets. Performance may vary between different manufacturers for the same chip.
More careful and comprehensive design consideration will result in better circuit board performance. However, ESD issues may still occur, so mechanical protection is also very important for ESD protection.

66. When Fabricating PCBs, Should Ground Wires Be Formed into Closed Loops to Reduce Interference?

When fabricating PCBs, the general principle is to minimize loop area to reduce interference. Therefore, when routing ground wires, they should not be laid out in closed form but rather in a tree-like structure, and the ground area should be maximized as much as possible.

67. If the Emulator Uses One Power Supply and the PCB Uses Another, Should the Grounds of the Two Power Supplies Be Connected?

Using separate power supplies is preferable as it reduces interference between them, but most devices have specific requirements. Given that the emulator and PCB use separate power supplies, in my opinion, their grounds should not be connected.

68. Should Multiple PCBs in a Single Circuit Share a Common Ground?

Most circuits composed of multiple PCBs require a common ground, as using multiple power supplies in a single circuit is generally impractical. However, if conditions permit, using separate power supplies will reduce interference.

69. Designing a Handheld Product with an LCD and Metal Enclosure. It Fails the IEC-1000-4-2 ESD Test: Contact Discharge Only Passes 1100V, Air Discharge Passes 6000V. During ESD Coupling Tests, Horizontal Only Passes 3000V and Vertical Only Passes 4000V. The CPU Clock Speed Is 33MHz. What Methods Can Be Used to Pass the ESD Test?

Handheld products with metal enclosures will have obvious ESD issues, and the LCD is likely to exhibit many adverse phenomena. If the existing metal material cannot be changed, it is recommended to add anti-static materials inside the enclosure, strengthen the PCB ground, and find ways to ground the LCD. Of course, the specific implementation depends on the actual situation.

70. What Aspects Should Be Considered for ESD When Designing a System Containing DSP and PLD?

For general systems, the main consideration is protection against direct human contact, with appropriate protection implemented at both the circuit and mechanical levels.
The extent to which ESD affects the system depends on specific circumstances. ESD phenomena are more severe in dry environments, and more sensitive and sophisticated systems are more significantly affected by ESD. While large systems may sometimes show less obvious ESD impacts, careful design consideration is still required to prevent problems before they occur.

About Maxipcb
Maxipcb empowers innovators to turn cutting-edge technologies into reality.
We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.