Categories

Common PCB Laminate Materials – Detailed Parameters and Applications

PCB substrates can be broadly classified into five categories based on the reinforcement material: paper‑based, fibreglass‑woven fabric‑based, composite‑based (CEM series), build‑up multilayer board substrates, and special‑material substrates (ceramic, metal‑core, etc.). When classified by the resin adhesive used, common paper‑based CCLs include phenolic resin types (XPC, XXXPC, FR‑1, FR‑2, etc.), epoxy resin types (FR‑3), and polyester resin types. Common fibreglass‑woven fabric‑based CCLs incl
Oct 3rd,2026 86 Views

PCB substrates can be broadly classified into five categories based on the reinforcement material: paper‑based, fibreglass‑woven fabric‑based, composite‑based (CEM series), build‑up multilayer board substrates, and special‑material substrates (ceramic, metal‑core, etc.). When classified by the resin adhesive used, common paper‑based CCLs include phenolic resin types (XPC, XXXPC, FR‑1, FR‑2, etc.), epoxy resin types (FR‑3), and polyester resin types. Common fibreglass‑woven fabric‑based CCLs include epoxy resin types (FR‑4, FR‑5) – FR‑4 is currently the most widely used fibreglass‑woven fabric substrate.

In addition, there are other specialty resins (with fibreglass fabric, polyamide fibres, non‑woven fabrics, etc. as reinforcement): bismaleimide triazine (BT), polyimide (PI), polyphenylene oxide (PPO), maleic anhydride imide‑styrene (MS), polycyanate ester, polyolefin resins, etc. Based on flame retardancy, CCLs are classified as flame‑retardant grades (UL94 V‑0, V‑1) and non‑flame‑retardant grades (UL94 HB). In recent years, with increasing environmental awareness, a new bromine‑free flame‑retardant CCL has emerged, often referred to as "green flame‑retardant CCL." With the rapid advancement of electronic products, higher performance requirements are placed on CCLs.

Therefore, CCLs can also be categorised by performance: general‑purpose CCLs, low‑dielectric‑constant CCLs, high‑heat‑resistant CCLs (with Tg typically above 150 °C), low‑CTE CCLs (commonly used for package substrates), etc.

PCB Material Classification by Quality Level (from lowest to highest):
94HB → 94V0 → 22F → CEM‑1 → CEM‑3 → FR‑4

Detailed parameters and applications:

  • 94HB: Standard paper‑based board, non‑flame‑retardant (lowest‑grade material, suitable for die‑punching, not for power supply boards).

  • 94V0: Flame‑retardant paper‑based board (die‑punching).

  • 22F: Single‑sided semi‑fibreglass board (die‑punching).

  • CEM‑1: Single‑sided fibreglass board (requires CNC drilling, cannot be die‑punched).

  • CEM‑3: Double‑sided semi‑fibreglass board (the lowest grade for double‑sided boards, apart from double‑sided paper boards; suitable for simple double‑sided designs, about RMB 5‑10/m² cheaper than FR‑4).

  • FR‑4: Double‑sided fibreglass board.

Flame‑Retardant Grade Classification: 94V‑0 → V‑1 → V‑2 → 94HB

Prepreg (PP) Thickness:

  • 1080 = 0.0712 mm

  • 2116 = 0.1143 mm

  • 7628 = 0.1778 mm

FR‑4 and CEM‑3 both indicate laminate types: FR‑4 is fibreglass‑reinforced epoxy laminate, while CEM‑3 is a composite substrate.


Dielectric Constant of PCB Materials

The dielectric constant (Dk) of PCB materials is studied because signal transmission speed and signal integrity on the PCB are both affected by Dk. This parameter is therefore very important. Hardware engineers often overlook it because the Dk value is determined once the manufacturer selects the material – for example, Shengyi PCB material has a Dk of about 3.7, while Chaosheng PCB material has a Dk of about 4.2.

The signal propagation speed on a PCB is given by the formula:

v = c / √Er

where *c* is the speed of light, and Er is the dielectric constant of the PCB material.

From this formula, common practical approximations are derived: approximately 6 mil/ps, or 6 inch/ns.

According to the Baidu Baike definition: the dielectric constant is the ratio of the electric field strength in a vacuum to that in a dielectric material when an external electric field is applied. It is frequency‑dependent.

The dielectric constant is the product of the relative permittivity and the absolute permittivity of free space. When a high‑Dk material is placed in an electric field, the field strength decreases significantly within the dielectric. The relative dielectric constant of an ideal conductor is infinite.

The polarity of polymer materials can be determined from their dielectric constant. Typically, materials with a relative dielectric constant >3.6 are considered polar; those between 2.8 and 3.6 are weakly polar; and those <2.8 are non‑polar.

Dielectric Constant of FR‑4 Laminate

The dielectric constant (Dk, ε, Er) determines the propagation speed of electrical signals in the medium. Signal speed is inversely proportional to the square root of Dk. The lower the Dk, the faster the signal travels. An analogy: imagine running on a beach with water covering your ankles – the viscosity of the water is like the dielectric constant; the more viscous (higher Dk), the slower you run.

Dielectric constant is not easy to measure or define. It depends not only on the material's intrinsic properties, but also on the test method, test frequency, and the material's condition before and during testing. Dk also varies with temperature – some specialty materials are designed with temperature compensation in mind. Humidity is another important factor, as water has a Dk of about 70; even a small amount of moisture can cause significant changes.

FR‑4 Laminate Dissipation Factor (Loss Tangent): The energy loss inside an insulating material under an electric field, caused by dielectric conduction and polarisation lag effects. It is also called dielectric loss or simply loss. Under an alternating electric field, the angle δ (complementary to the power‑factor angle Φ) between the current phasor and voltage phasor is the dielectric loss angle. The dissipation factor of FR‑4 is generally around 0.02 and increases with frequency.

FR‑4 Laminate Tg (Glass Transition Temperature): Typical values are 130 °C, 140 °C, 150 °C, and 170 °C.

Common FR‑4 Laminate Thicknesses:

Commonly used thicknesses: 0.3 mm, 0.4 mm, 0.5 mm, 0.6 mm, 0.8 mm, 1.0 mm, 1.2 mm, 1.5 mm, 1.6 mm, 1.8 mm, 2.0 mm. Thickness tolerances depend on the manufacturer's capability.

Common Copper Foil Thicknesses for FR‑4 Copper‑Clad Laminate: 0.5 oz, 1 oz, 2 oz. Other thicknesses are also available – please consult your PCB manufacturer for confirmation.

About Maxipcb

Maxipcb empowers innovators to turn cutting-edge technologies into reality.We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.