Categories

A Brief Discussion on PCB Testing Technologies and Methods

An indispensable part of the PCB production and manufacturing process is to inspect the assembled PCB according to its functionality and manufacturability.
Jun 17th,2026 135 Views
Today we will talk about PCB testing technologies and PCB testing methods.

I. What is Design for Testability (DFT) in PCB Manufacturing?

An indispensable part of the PCB production and manufacturing process is to inspect the assembled PCB according to its functionality and manufacturability.
There is a very professional term for this: Design for Testability (DFT). In fact, it is a series of inspections performed on the PCB after reflow soldering, wave soldering, or reflow soldering + wave soldering, such as X-ray, AOI, ICT, and FCT inspections.
Of course, for engineers who have worked in PCB factories for a long time, these are commonplace.
Slightly different from DFM, DFM avoids risks, finds problems, and solves problems before production and manufacturing; while DFT inspects and solves problems during the production and manufacturing process.
Although different, both are equally important. AiPCBA
Professionally speaking: PCB Design for Testability (DFT) is a method for performing operational and functional tests on circuit boards and layout optimizations. PCB DFT can identify any short circuits, open circuits, incorrect component placement, or faulty components.
Design for Testability (DFT) is mainly to verify the following three issues:
  1. Is the circuit board design accurate?
  2. Is the circuit board manufacturing perfect? Are there any defects?
  3. Are all components, chips, and connections on the PCB board functioning properly?
There are also some issues that need to be addressed:
  1. Components should be properly spaced to reduce the risk of test defects
  2. If the solder mask between pads is incorrect, the electrical performance of the PCB may degrade
  3. Optimize drill bit sizes
  4. Solve the problem of inappropriate surface mount pad sizes
  5. Acid trap detection

II. Parameters Included in PCB Manufacturing Design for Testability (DFT)

1. Test Points

Test point insertion is a necessary technology in DFT to improve test efficiency. The position of a test point depends on how many components it can cover. Signal integrity issues can be alleviated by arranging accurate power and ground test points.

2. Test Traces

You can place test points on analog sensitive traces. These test points can be connected to an oscilloscope or signal generator to understand the behavior of the signal.

3. LEDs

LEDs can be added to determine whether the power is on or off. Debug LEDs are very suitable for FPGAs or microcontrollers and are used in mass production.

4. Connectors

Test points connected to vias are used to measure the voltage on the vias.

III. What are the Technologies for PCB Manufacturing Design for Testability (DFT)?

1. PCB Bare Board Testing

Bare board testing is performed before component assembly to check the connectivity of the PCB. The following are two methods for performing such tests:
  • Isolation test verifies the resistance between two electrical connections.
  • Continuity test checks for open circuits within the board.

2. PCB Assembled Board Testing

Assembled board testing is performed after component assembly. This process ensures the integrity of the circuit board and the realization of component functions.

IV. 7 PCB Testing Technologies

1. Flying Probe Test

Both PCB bare boards and assembled boards can be tested with flying probe tests in passive and active modes respectively.
Probes include needles for inspection, and test points can include passive components such as resistors, capacitors, inductors, non-porous vias, or termination ends of components. It can detect the values of unpowered components, open or short circuits, measure voltages, and check the positions of diodes and transistors.
Advantages of Flying Probe Test:
  • Cheaper
  • Greater test coverage
  • No fixtures required
  • Fast implementation
Disadvantages of Flying Probe Test:
  • Very time-consuming as the probe moves between measurement points
  • Difficult to set up if the circuit board does not include any test points, test vias, or mask vias
  • Discrete capacitors can only be tested for parallel capacitors

2. In-Circuit Test (ICT)

ICT testing includes a number of pre-installed electronic probes aligned under the circuit board through preset access points. This establishes an accurate and stable electrical connection between the probes and the PCB. The test probes allow current to flow at predetermined design test points.
ICT can check for short or open circuits, solder mask defects, component misalignment or missing components, etc. This method includes test fixtures to properly hold the circuit board with probes, and test fixtures to simultaneously check multiple components on the circuit board. This test method can save time.
Advantages of ICT Test:
  • Used for mass production
  • Provides up to 90% coverage
  • Accurate
  • Free from human error
Disadvantages of ICT Test:
  • Not suitable for small-batch production
  • Cannot detect voids or insufficient solder mask
  • Expensive
  • Technologies such as test fixtures increase costs

3. Functional Circuit Test (FCT)

FCT testing is used for quality control and to ensure the expected operation of the equipment. Test parameters are provided by the customer/designer according to the design.
This technology usually includes simple switch tests, and sometimes it requires complex software and precise protocols. Functional testing directly checks the function of the circuit board under real environmental conditions.
Advantages of FCT Test:
  • Low cost
  • Versatile and customizable according to design
  • Does not affect the service life of the circuit board unlike other tests that apply excessive stress to it
Disadvantages of FCT Test:
  • Requires experienced technicians

4. Automated Optical Inspection (AOI)

AOI includes 2D or 3D cameras that capture high-resolution images and verify against the schematic. It also compares with perfect and imperfect designs available in the database. AOI can find all visible errors very accurately.
AOI is used in conjunction with another test method to ensure correct results, such as AOI with flying probe, and AOI with in-circuit test.
AOI can be directly included in the production line to prevent any premature circuit board failures.
Advantages of AOI Test:
  • Can accurately detect fatal defects
  • Consistent method
Disadvantages of AOI Test:
  • Can only detect surface defects
  • Time-consuming process
  • Settings change according to design
  • Database-based detection is not always 100% accurate

5. Burn-in Test

Burn-in testing is an early inspection of circuit boards to prevent dangerous failures after manufacturing is completed. This method involves exceeding specified operating limits to trigger failures. It is an effective method to detect the maximum operating rating of a circuit board.
Various operating conditions involve voltage, current, temperature, operating frequency, power, and other factors related to the design.
Advantages of Burn-in Test:
  • Improves product reliability
  • Verifies the function of the circuit board under environmental conditions
Disadvantages of Burn-in Test:
  • Applying stress beyond the rated value shortens the service life of the circuit board
  • This process requires more time and more effort

6. X-ray Inspection

X-ray inspection uses X-ray imaging to detect errors in hidden components, solder connections, BGA packages, internal traces, and barrels.
Advantages of X-ray Inspection:
  • No need to inspect each layer of the PCB
  • X-ray machines can easily inspect internal layers from the top of the circuit
Disadvantages of X-ray Inspection:
  • Requires experienced and skilled technicians
  • This process requires more labor and cost

7. Manual Visual Inspection

Here, technicians perform inspections with the naked eye or using a magnifying glass. Manual visual inspection can determine misalignment of unexposed components, missing components, and other defects.
Advantages of Manual Visual Inspection:
  • Simple and basic method
Disadvantages of Manual Visual Inspection:
  • Affected by human error
  • Cannot detect tiny and invisible defects

V. 9 PCB Testing Methods

1. Border Edge Width

This is crucial for maintaining sufficient, unoccupied space on the opposite edges of the circuit board. Clear edges help to perfectly secure the testing machine.

2. Fiducial Points

Machines need some reference points to know the exact position of the probes. Reference points (called fiducials) are located on the panel scrap, or on the PCB itself if the scrap has been removed. The most suitable and recommended fiducials are the top-left and bottom-right corners of the board.

3. Vias

Vias included in the circuit board design do not need to be covered so that probes can be placed on their edges.

4. Component Pins

Generally, it is best to place test probes near component legs for good solder joints, although component pins do not need to be tested. This technique connects any potential open circuit at the test point by pushing the component leg onto the pad.

5. Size

If you are designing a relatively large PCB, keep the test access points as close as possible.

6. Cleanliness

Cleaning components is crucial to ensure the removal of unwanted flux. This is because sometimes the tester has to move the probe position to get better contact, and unwanted flux can cause failures and increase test time.

7. Probe Points

You can introduce accessible probe points in the ground and power rails on the bottom side, which can be on the unprobed side of the PCB. This allows fixed probes to act as temporary fixtures, speeds up short circuit testing, and can reduce overall test time and cost.

8. Test Access

If possible, maximize test access on one side of the assembly, with at least one possible point per network. If you are using a double-sided machine, the cost of flipping the circuit board to test both sides increases.

9. Component Height

There are maximum allowable component heights in both probed and unprobed areas of the PCB, typically about 40mm and 90mm respectively. If tall components are not probed or installed after testing, place them on the bottom side. They can create a no-fly zone over components and can also hinder test access.
Design for Testability (DFT) is fundamentally a review process to find and fix any manufacturing errors, check customer-provided specifications, and minimize redundant processes. Without such regular testing, PCB manufacturers may face serious production errors. DFT ensures that high-yield circuit boards are manufactured at the lowest cost.

About Maxipcb
Maxipcb empowers innovators to turn cutting-edge technologies into reality.
We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.