Power dividers and combiners are among the most common and frequently used high‑frequency components, and the same holds true for couplers such as directional couplers. These devices are used to divide, combine, or couple high‑frequency energy from antennas or within systems, with minimal loss and leakage. The choice of PCB material is a critical factor in achieving the intended performance of these components. When designing and fabricating power dividers/combiners and couplers, it is helpful to understand how the properties of PCB materials affect the final performance of these devices – for example, it helps to define constraints on a range of performance parameters for the chosen laminate, including frequency range, operating bandwidth, and power‑handling capability.
Many different circuit topologies are used to design power dividers (and, conversely, combiners) and couplers, and they come in various forms. Power dividers range from simple two‑way divisions to complex N‑way divisions, depending on the actual system requirements. A wide variety of directional couplers and other coupler types have also been developed over the years, including Wilkinson and resistive dividers, as well as Lange couplers and quadrature hybrid bridges, in many different forms and sizes. Choosing the right PCB material for these circuit designs helps to achieve optimal performance.
These different circuit types all involve trade‑offs between design structure and performance, helping designers select laminates for different applications. A Wilkinson two‑way power divider provides two equal‑amplitude and in‑phase output signals from a single input. It is essentially a "lossless" circuit, designed to deliver two output signals that are 3 dB lower (i.e., half the power) than the original signal (the output power at each port decreases as the number of output ports increases). In contrast, a resistive two‑way divider provides two output signals that are 6 dB lower than the input. The added impedance in each branch of the resistive divider increases loss, but also improves isolation between the two output ports.
As with many circuit designs, the dielectric constant (Dk) is generally the starting point for selecting different PCB materials, and designers of power dividers/combiners tend to prefer high‑Dk circuit materials because they provide effective electromagnetic coupling in smaller circuit dimensions compared to low‑Dk materials. One issue with high‑Dk circuits is that the Dk may exhibit anisotropy – meaning that the dielectric constant values differ in the x, y, and z directions. When the Dk varies significantly even within the same direction, it becomes difficult to achieve uniform impedance transmission lines.
Maintaining impedance uniformity is very important in achieving the desired characteristics of power dividers/combiners, as variations in Dk (and hence impedance) lead to uneven distribution of electromagnetic energy and power. Fortunately, commercial PCB materials with excellent isotropy are available for such circuits, such as TMM 10i circuit material. This material has a relatively high Dk of 9.8 and maintains that value within ±0.245 in all three axes (measured at 10 GHz). This means that uniform impedance characteristics in the transmission lines of power dividers/combiners and couplers ensure constant and predictable distribution of electromagnetic energy within the device. For even higher‑Dk PCB materials, TMM 13i laminate offers a Dk of 12.85 with variations within ±0.35 in all axes (at 10 GHz).
Of course, constant Dk and impedance characteristics are only some of the PCB material parameters to consider when designing power dividers/combiners and couplers. Minimising insertion loss is often a key goal in such designs. Ideally, a two‑way Wilkinson divider delivers ‑3 dB, or half, of the input electromagnetic energy to each output port. In practice, every divider/combiner (and coupler) circuit has some insertion loss, which typically depends on frequency (increasing with frequency). Therefore, the choice of PCB material for a divider/combiner design must take into account how to control and minimise circuit insertion loss.
In passive high‑frequency components such as power dividers/combiners or couplers, insertion loss is actually the sum of many loss mechanisms, including dielectric loss, conductor loss, radiation loss, and leakage loss. Some of these losses can be controlled through careful circuit design; they may also depend on PCB material properties and can be minimised by proper material selection. Impedance mismatch (i.e., SWR loss) can contribute to loss, but it can be reduced by choosing PCB materials with consistent Dk.
Minimising loss is particularly critical in high‑power dividers/combiners and couplers, because at high power levels, losses are converted into heat dissipated in the device and the PCB material, and heat can affect the Dk (and therefore impedance) of the material.
In summary, when designing and fabricating high‑frequency power dividers/combiners and couplers, the choice of PCB material should be based on a number of key material properties, including Dk value, consistency of Dk within the material, environmental factors such as temperature, loss reduction (including dielectric and conductor losses), and power‑handling capability. Selecting the appropriate PCB material for the specific application will help ensure success in high‑frequency divider/combiner or coupler designs.
About Maxipcb