Categories

Engineer's Design Tips: Essentials of PCB Grounding

Analog ground / digital ground and analog power / digital power are essentially relative concepts. The main reason for introducing these distinctions is that the interference from digital circuits on analog circuits has become unacceptable.
Aug 25th,2026 160 Views

Analog ground / digital ground and analog power / digital power are essentially relative concepts. The main reason for introducing these distinctions is that the interference from digital circuits on analog circuits has become unacceptable. The current standard approach is as follows:

  1. After rectification and filtering, the ground line is split into two branches: one serves as the analog ground, to which all ground connections of the analog circuitry are tied; the other serves as the digital ground, to which all ground connections of the digital circuitry are tied.

  2. After the DC voltage regulator output is filtered, it is similarly split into two branches: one passes through an LC/RC filter to become the analog power supply, powering all analog circuits; the other becomes the digital power supply, powering all digital circuits.

Note: The analog ground / digital ground and analog power / digital power must have no connection other than a single point at the very beginning of the power distribution.

  • AVCC: analog power supply

  • AGND: analog ground

  • DVCC: digital power supply

  • DGND: digital ground

This separation is intended to isolate the digital and analog sections, reducing interference from the digital circuitry to the analog circuitry. However, the two sections cannot be completely isolated – they are interconnected by signal paths. Therefore, at minimum, the grounds must be connected together. A 0 Ω resistor, a ferrite bead, or an inductor is typically used to connect AGND and DGND at a single point. Such a single‑point connection helps reduce interference. Similarly, if both sections share the same supply voltage, the same approach should be adopted.

In electronic system design, to save time and avoid rework, adequate consideration should be given to anti‑interference requirements from the start, rather than adding remedial measures after the design is complete. There are three basic elements that constitute interference:

(1) Interference source – components, devices, or signals that generate interference. In mathematical terms, places with large du/dt or di/dt are interference sources. Examples include lightning, relays, thyristors, motors, and high‑frequency clocks.

(2) Propagation path – the pathway or medium through which interference travels from the source to the sensitive device. Typical propagation paths are conduction via wires and radiation through space.

(3) Sensitive devices – components that are easily affected by interference, such as A/D and D/A converters, microcontrollers, digital ICs, and low‑level signal amplifiers.

The basic principles of anti‑interference design are: suppress the interference source, cut off the propagation path, and improve the immunity of sensitive devices.

(Analogous to the prevention of infectious diseases.)


1. Suppressing the Interference Source

Suppressing the interference source means reducing its du/dt and di/dt as much as possible. This is the highest‑priority and most important principle in anti‑interference design, often yielding substantial results with relatively little effort. Reducing du/dt is mainly achieved by connecting a capacitor in parallel across the interference source. Reducing di/dt is achieved by adding an inductor or resistor in series with the source loop, or by adding a freewheeling diode.

Common measures for suppressing interference sources:

(1) Add a freewheeling diode across the relay coil to eliminate back‑EMF interference when the coil is de‑energised. Using only a freewheeling diode delays relay release; adding a Zener diode allows the relay to operate more times per unit time.

(2) Connect a spark‑suppression circuit (typically an RC series network, with R in the range of a few kΩ to tens of kΩ and C ≈ 0.01 μF) across relay contacts to reduce spark impact.

(3) Add a filter circuit to motors, keeping capacitor and inductor leads as short as possible.

(4) Place a 0.01 μF to 0.1 μF high‑frequency decoupling capacitor in parallel with each IC on the board to reduce the IC's impact on the power supply. Pay attention to routing – the capacitor leads should be close to the power pins and as short and wide as possible; otherwise, the equivalent series resistance (ESR) increases and filtering effectiveness degrades.

(5) Avoid 90° trace bends to reduce high‑frequency noise emission.

(6) Connect an RC snubber across thyristors to reduce the noise they generate (which, in severe cases, may destroy the thyristor).

Interference can be classified by propagation path into conducted interference and radiated interference.

Conducted interference propagates to sensitive devices through wires. Since high‑frequency noise and useful signals occupy different frequency bands, filters can be added on the wires to block high‑frequency noise. Optical isolators may also be used. Power‑supply noise is particularly harmful and deserves special attention.

Radiated interference propagates to sensitive devices through space. Common solutions include increasing the distance between the interference source and sensitive devices, using ground traces for isolation, and adding shielding covers over sensitive devices.


2. Common Measures to Cut Off Interference Propagation Paths

(1) Give full consideration to the impact of the power supply on the microcontroller. A well‑designed power supply solves a large portion of the system's noise problems. Many microcontrollers are sensitive to power‑supply noise; a filter circuit or regulator should be added to the MCU power supply to reduce noise. For example, a pi‑filter using a ferrite bead and capacitors can be used; if requirements are less stringent, a 100 Ω resistor may replace the ferrite bead.

(2) If the MCU's I/O ports control noisy devices such as motors, isolation (e.g., an additional pi‑filter circuit) should be added between the I/O port and the noise source.

(3) Pay attention to crystal oscillator routing. Place the crystal as close as possible to the MCU pins, isolate the clock area with a ground guard ring, and ground the crystal case securely. This measure can resolve many obscure problems.

(4) Partition the board properly – separate strong and weak signals, digital and analog signals. Place interference sources (e.g., motors, relays) as far as possible from sensitive components (e.g., microcontrollers).

(5) Use ground traces to isolate the digital area from the analog area. Separate digital and analog grounds and connect them at a single point to the power supply ground. This principle also applies to A/D and D/A converter routing; chip manufacturers often consider this requirement when arranging pinouts.

(6) Provide separate ground returns for the microcontroller and high‑power devices to reduce mutual interference. Place high‑power devices near the edge of the board when possible.

(7) Use anti‑interference components such as ferrite beads, ferrite rings, power line filters, and shielding cans at critical locations – including MCU I/O ports, power lines, and board connectors – to significantly improve circuit immunity.


3. Improving the Noise Immunity of Sensitive Devices

Improving the immunity of sensitive devices involves reducing the pickup of interference noise from the device side and restoring normal operation as quickly as possible after abnormal conditions.

Common measures to improve noise immunity of sensitive devices:

(1) Minimise the loop area of traces to reduce induced noise.

(2) Make power and ground traces as wide as possible. Besides reducing voltage drop, this is even more important for lowering coupling noise.

(3) Do not leave unused MCU I/O pins floating; tie them to ground or power. For other ICs, unused pins should also be tied to ground or power, provided this does not alter system logic.

(4) Use power‑supply monitors and watchdog circuits (e.g., IMP809, IMP706, IMP813, X25043, X25045) to greatly improve overall system immunity.

(5) Use the lowest possible crystal frequency and low‑speed digital logic, as long as speed requirements are met.

(6) Solder ICs directly onto the board whenever possible; minimise the use of IC sockets.

To achieve good noise immunity, we often see ground‑plane splitting on PCBs. However, not every mixed digital‑analog design requires ground plane splitting – it is done specifically to reduce noise interference.

Theory: Digital circuits generally operate at higher frequencies than analog circuits, and their signals form return currents with the ground plane (because, during signal transmission, there are various parasitic inductances and distributed capacitances between traces). If the grounds are combined, these return currents will cross‑couple between the digital and analog sections. Separating them confines the return currents to their respective loops. A 0 Ω resistor or ferrite bead connects them because they are physically the same ground; after being separated in layout, they must be reconnected at a single point.

How to determine whether a component belongs to the analog or digital section? This is a common question during PCB layout. My personal view is that the decision should be based on the primary chip associated with the component. For example, a power supply that powers analog circuits belongs to the analog section; if it powers a microcontroller or data‑type chip, it belongs to the digital section. When they share the same power supply, a bridge must be used to route power from one section to the other. A typical example is a D/A converter – it is half digital and half analog. If the digital inputs are handled properly, the rest can be placed in the analog section.

Analog circuits involve small signals, but digital circuits have higher threshold levels and thus less demanding power requirements. In a system containing both, digital circuit noise can affect analog circuits and degrade their small‑signal performance. The solution is to separate analog and digital grounds.

For low‑frequency analog circuits, in addition to making ground traces thicker and shorter, a single‑point ground connection for each circuit section is the best way to suppress ground interference – primarily to prevent mutual interference between sections caused by common‑impedance coupling.

For high‑frequency circuits and digital circuits, however, the inductive effect of ground traces becomes more significant, and single‑point grounding may actually lengthen ground paths, causing adverse effects. In such cases, a combination of separate and single‑point grounding should be used.

For high‑frequency circuits, measures to suppress radiated noise include: making ground traces as wide as possible to reduce ground impedance; and using full‑ground (flooding all unused areas with ground copper) – but avoid large useless copper areas.

Ground traces should form a loop to prevent high‑frequency radiation noise, but the loop area must not be too large, otherwise induced currents may flow when the equipment is in a strong magnetic field. For low‑frequency circuits, however, ground loops should be avoided.

Digital and analog power supplies are best isolated, with grounds routed separately. If an A/D converter is present, only at that point should the grounds be connected together.

At low frequencies, there is little impact, but a single‑point analog‑digital ground connection is still recommended. At high frequencies, the analog and digital grounds can be connected at a single point via a ferrite bead.

If the analog and digital grounds are directly connected over a large area, mutual interference will result. However, leaving them disconnected is also problematic for the reasons mentioned above. There are four common ways to address this:

  1. Connect with a ferrite bead – its equivalent circuit is a band‑stop filter, effective only at a specific frequency. The noise frequency must be known beforehand to select the correct type. Not suitable for unknown or variable frequencies.

  2. Connect with a capacitor – blocks DC and causes a floating ground.

  3. Connect with an inductor – bulky, with many parasitic parameters and instability.

  4. Connect with a 0 Ω resistor – provides a very narrow current path, effectively limiting loop current and suppressing noise. A resistor provides attenuation across all frequencies (0 Ω resistors also have some impedance), which is superior to a ferrite bead in this regard.

    About Maxipcb

    Maxipcb empowers innovators to turn cutting-edge technologies into reality.We offer one-stop solutions for design, simulation, testing, PCB manufacturing, component procurement and SMT assembly, enabling efficient development, rapid deployment and risk control across the full product lifecycle.
    Serving the world in communications, industrial automation, aerospace, automotive, semiconductor and beyond, we build a safer, more connected future together.