1. Why Is PCB Interconnect Flat Cable So Important for EMC?
During interconnection, not only do different signals come close to each other, causing crosstalk, but more importantly, the impedance of the ground interconnection signal path in the connector is much higher than that of a ground plane design in a multi‑layer PCB. As a result, similar to what happens on a PCB, when an external common‑mode interference current flows through, the circuits interconnected between connectors will be disturbed. When the return current of signals flowing through the interconnecting circuits between connectors passes through the high‑impedance ground interconnection signal, it generates common‑mode EMC issues.
2. What Is the Difference Between Diode Clamping and TVS Protection?
Both diodes and TVS devices can be used for transient interference protection, but their protection principles are different. A diode works on its forward conduction characteristic, while a TVS works on its reverse breakdown principle. Compared with TVS devices, diodes generally have lower junction capacitance – this trade‑off must be carefully considered during design.
3. What Should Be Considered for Inter‑Product Bonding in EMC Issues?
Inter‑product interconnections typically involve crosstalk and separation of ground reference levels, and the signal crosstalk between them is generally higher than that between multi‑layer PCBs. Therefore, when interconnecting products, special attention must be paid to the bonding between them. Zero‑potential bonding is essential to avoid EMC problems.
4. How Should Differential Signal Pairs Be Routed in PCB Design?
Differential signal pairs should be routed in parallel, with equal trace lengths, and on the same layer. During routing, avoid right‑angle bends or inconsistent trace widths, and avoid placing differential pairs near the edge of the PCB. Any trace‑length extension needed to compensate for offset between complementary output signals should be placed close to the driver.
5. What Is a Ferrite Bead and How Should It Be Correctly Selected?
Ferrite beads are specifically designed to suppress high‑frequency noise and spike interference on signal lines and power lines, and they also have the ability to absorb electrostatic pulses. The main function of a ferrite bead is to eliminate RF noise present in transmission‑line structures (circuits). It acts as a high‑frequency resistor, allowing DC signals to pass while filtering out AC signals. High‑frequency signals are generally considered to be above 30 MHz; however, lower‑frequency signals can also be affected by ferrite beads. To select the correct ferrite bead, the following points should be noted:
What is the frequency range of the unwanted signal?
What is the source of the noise?
How much noise attenuation is required?
By examining the impedance‑versus‑frequency curves provided by the manufacturer, choose a bead model that offers maximum impedance in the frequency range where attenuation of noise is desired, while causing minimal signal attenuation at low frequencies and DC.
6. Comparison of Signal Reception Error Rates Between Spectrum Analysers and Receivers
A spectrum analyser obtains signal data by sweeping from a start frequency to a stop frequency at a fixed scanning rate. Because the scanning speed is fixed and generally faster than that of a receiver, it may not be able to keep up with certain frequency variations, particularly for broadband noise generated by transient and pulsed RF signals, leading to data acquisition errors. In contrast, receiver scanning is adjustable; in particular, when detecting lower‑frequency signals, a low dwell time setting can be used to capture low‑frequency signals. This adjustable dwell time allows the detection of data that varies with different parameters.
7. How Should EMC Design Be Performed for Clock Circuits?
Clock circuits are a major source of electromagnetic compatibility radiation. The following points should be noted in clock circuit design:
Calculate and control the characteristic impedance, phase constant, attenuation constant, and other parameters of microstrip lines and microstrip waveguides formed by various traces.
Calculate the delay experienced by clock pulses. When the delay reaches a certain value, impedance matching must be performed to avoid reflections at the transmitting terminal, which can cause signal jitter or overshoot.
8. How Should Filters Be Placed?
Filters should be installed as close as possible to the port where noise suppression is required.
When designing and installing filters, both transient voltages in the power grid and surge currents caused by electrical equipment must be considered, to ensure that the filter is not damaged.
High‑current filters may have significant power losses, with most of the energy dissipated in the choke coil. Therefore, effective cooling must be ensured, and the choke should be placed as far as possible from the filter capacitor.
Power electronic equipment often generates non‑sinusoidal grid‑side currents with strong low‑order harmonics, which may cause noticeable low‑frequency noise. To reduce this noise, the inductor coils should be impregnated and the iron cores bonded.
9. How Should the Design of a Shielding Enclosure Be Considered?
First, determine the electromagnetic environment that the shielding design is intended to address.
Determine the sensitivity of the circuits most susceptible to interference, in order to define the shielding requirements for the complete enclosure.
Design considerations must include openings, cable exits, and other penetrations of the shield.
Ensure proper interconnection and bonding between the various components of the shielding enclosure.
10. What Should Be Considered When Shielding a Magnetic Field Radiation Source?
Because the wave impedance of a magnetic field is very low, reflection loss is minimal, and shielding is primarily achieved through absorption loss. Therefore, it is important to choose a shielding material with high magnetic permeability. Additionally, during structural design, the shield should be placed as far as possible from the radiation source (to increase reflection loss), and holes, gaps, and similar features should be kept away from the radiation source.
About Maxipcb