WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

How Do SMT and DIP Assembly Work Together in PCB Production?

By maxipcb November 11th, 2026 12 views

Introduction: Mixed-technology boards pass through two very different soldering processes, and the order they follow explains most of what happens on the line.

Most industrial circuit boards are neither purely surface-mount nor purely through-hole. They carry a dense field of chip components on one side and a handful of connectors, relays, or terminal blocks whose leads must pass through the board. Learning to read a mixed board as a sequence rather than a parts list makes the whole assembly flow easier to follow, and it explains why the two processes stay separate instead of being merged into a single pass. That sequence — place first, insert later — is the thread running through this explanation.

What SMT Placement and DIP Insertion Do Differently on a Mixed Board

SMT is the part of the line that handles components sitting flat on the board surface. Chip resistors and capacitors, SOICs, QFNs, and fine-pitch ICs have no leads to push through anything. They land on solder-paste deposits printed onto copper pads, and the joint forms when the whole board travels through a reflow oven. Placement is fast and highly repeatable, which is why the dense, small components on an industrial control board are almost always surface-mount. Solder paste is the lever that makes this work. A stainless stencil with laser-cut apertures deposits a controlled volume of paste on each pad, and NXP's surface-mount reflow guidance treats aperture design and print consistency as primary drivers of joint quality. Get the volume right and a QFN or a 0402 chip seats cleanly; get it wrong and the part floats, tilts, or bridges across two pads. DIP covers the other half of the board. Connectors, terminal blocks, relays, transformers, radial electrolytic capacitors, and power devices have metal leads that pass through drilled, plated holes and are soldered on the opposite side. Solder must flow into the barrel and form a fillet on both faces of the board, which is a different physical event from a reflow joint and needs a different heat source: a solder wave, a localized selective nozzle, or an iron for very small runs. Neither process replaces the other, because the packages themselves are not interchangeable.

Why Mixed-Technology Boards Need a Defined Sequence Between SMT and DIP

The order exists because the two processes interfere with each other when run the wrong way around. Pushing through-hole parts through a reflow oven exposes them to a full thermal cycle their bodies were never designed for, and inserting leads before paste printing means the stencil can no longer sit flush against the surface. A mixed board therefore follows a place-first, insert-later pattern, with four distinct stages.

  • Paste deposition happens on a bare board with the through-holes still open. The stencil is a flat sheet that has to sit tight against the surface, so any component already standing on the board, or any lead poking through a hole, would hold it off the pads and smear the print.
  • Reflow consolidates every surface-mount joint in one thermal pass. The board moves through preheat, soak, reflow, and cooling zones; the paste alloys, wets the pads, and solidifies into joints. Every part present at this moment sees the peak temperature of the profile.
  • Through-hole insertion comes after reflow, when the holes are clear and the surface is flat again. Leads drop in, and components whose bodies would not survive the oven — plastic connectors, wet electrolytic capacitors, many relays — can now be added without thermal risk.
  • Final soldering completes the through-hole joints, usually with wave or selective soldering. The surface-mount side is masked or shielded so molten solder only touches intended areas, and the board leaves the line with both joint types finished.

Reading the sequence this way clears up a common misunderstanding. SMT and DIP are not two alternative routes to the same result; they are two stages that answer different mechanical and thermal problems, and the order is what keeps one stage from damaging the work of the other.

How Thermal Exposure and Component Form Shape the Assembly Sequence

Two properties decide where a part lands in the sequence: how much heat its body can absorb, and what shape its termination has. Reflow is not gentle. Boards pass through a profile with a controlled ramp, a soak that lets flux activate and volatiles escape, a short window above liquidus, and a cooling slope that determines grain structure. Texas Instruments' reflow recommendations describe this balance directly — enough heat to form a reliable joint, not so much that packages, molds, or internal connections degrade. NXP's thermal profile guidance makes the same point across package families, where body size and leadframe mass change how quickly a part reaches peak temperature. Component form matters just as much. A leaded connector with a tall plastic housing can absorb oven heat slowly and distort; a moisture-sensitive package that has taken on humidity can crack internally when it hits reflow, which is why parts are dried and stored before use. Large terminals and heavy copper planes also act as heat sinks, pulling energy away from the joint during through-hole soldering, and selective nozzles exist largely to concentrate heat where a wave would spread it too widely. Some designs deliberately place a few through-hole parts before reflow using a pin-in-paste approach, but that is a layout decision rather than the default. The practical takeaway is that the sequence follows the parts, not the other way round. A board with a tall plastic connector and a wet electrolytic capacitor will push those parts after reflow, while a board dominated by fine-pitch surface-mount devices will spend its thermal budget on a tight reflow window. The exact order can shift with board design, component mix, and the fabricator's process. Maxipcb's turnkey PCBA service listing, for instance, covers both SMT and DIP assembly alongside nitrogen reflow, imported solder paste and solder bars, and IPC-A-610-oriented workmanship — a package that only makes sense because the two processes run as coordinated stages rather than a single step.

Conclusion

SMT and DIP divide a mixed board by component form and thermal tolerance, and the place-first-then-insert sequence is what keeps both halves reliable. Surface-mount parts are printed, placed, and reflowed while the through-holes stay clear; leaded parts are inserted afterwards and soldered with a process that localizes heat instead of bathing the whole board. Understanding that order gives process learners a way to read any mixed assembly and predict why a given part sits where it does, and it turns a parts list into a story about heat, holes, and timing.

FAQ

Q: How do SMT and DIP assembly differ on a mixed-technology PCB?

A: SMT handles components that sit flat on printed pads, such as chip resistors, capacitors, SOICs, and QFNs, joined by reflowing solder paste. DIP handles components with leads that pass through plated holes, such as connectors, relays, and electrolytic capacitors, joined by wave, selective, or hand soldering. The two differ in component form, joint geometry, and the heat source used to form the connection.

Q: Why does SMT placement usually happen before DIP insertion?

A: Because the surface-mount stage depends on a flat, unobstructed board. A stencil must sit flush to print paste, and reflow uses a single thermal pass that finishes every surface joint at once. Any lead already through a hole, or any component body already standing on the board, would interfere with printing, and any through-hole part present during reflow would absorb a thermal cycle it was not built for.

Q: Why do mixed boards need both reflow and through-hole processes?

A: Because the two processes solve different problems. Reflow gives dense, small, leadless components a fast and repeatable joint, while through-hole soldering gives connectors, power devices, and mechanical parts the barrel fill and physical strength that surface mounting cannot provide. Many industrial designs also depend on packages that only exist in a leaded form, so the board needs both stages to be complete.

Sources / References

PCB Handling and Solder Reflow Recommendations - Texas Instruments

NXP Application Note AN10365: Surface Mount Reflow Soldering Partner Guide

NXP Application Note AN1902: Assembly Guidelines for QFN Packages

Related Examples

Maxipcb Turnkey PCB Assembly

Previous
Turnkey PCB Assembly with BOM Sourcing for Prototype Builds
Read More
Next
DFM Review Starts With Pad and Stencil Design in Fine-Pitch Layouts
Read More