WELCOME TO OUR BLOG

We're sharing knowledge in the areas which fascinate us the most
click

Custom PCB Assembly with SMT and DIP for Mixed-Technology Boards

By maxipcb September 10th, 2026 132 views

Introduction: Custom PCB assembly of a mixed-technology board succeeds when SMT packages are reflowed, through-hole DIP parts are wave soldered, and the service reviews the physical board data before committing to a process plan.

A board with a QFN microcontroller, fine-pitch memory, and small passive components often also needs connectors, relays, transformers, or terminal blocks that are better soldered through drilled holes. SMT packages suit dense circuitry, while DIP packages suit parts that need mechanical retention or a larger conductive path through the board. One assembly service must therefore handle reflow soldering for the SMT side and wave soldering for the DIP side without damaging either joint type. For a hardware team preparing a custom PCB assembly order, the deciding point is not whether the supplier owns both process types, but whether the process sequence and documentation review protect both joint structures.

Why a Mixed-Technology Board Creates Both SMT and DIP Solder Joints

SMT and DIP solder joints are physically different. An SMT joint forms on copper land pads on the board surface: solder paste is printed, the component is placed onto the paste, and reflow soldering melts the paste to connect the component termination to the pad. A DIP joint forms inside the board: the component lead is inserted through a drilled hole, and wave soldering wets the lead, the annular pad, and the plated copper inside the barrel. The through-hole connection extends through the board thickness, which gives it more mechanical strength and a larger conductive path. These physical differences decide what must be examined before production. SMT reliability is set by the land pattern, the solder mask opening, and the stencil aperture that controls solder paste volume; those layout-stage decisions are covered by references such as Analog Devices AN-772 and STMicroelectronics AN2639. Through-hole reliability is set by the hole diameter, board thickness, plated barrel copper, and component thermal mass. A mixed board exists because the two package families solve different engineering problems. QFN, QFP, BGA, DFN, SOT/SOP, and small passive components make it possible to fit dense circuitry into a compact area. Connectors, relays, fuse holders, terminal blocks, and magnetic or power components need a stronger anchor than a surface pad can provide. An SMT connector can pass reflow soldering but may crack at the pad after repeated insertion cycles. A through-hole connector distributes that stress through the plated barrel and around the lead, which is why many industrial, power, and measurement designs keep those parts in DIP form. A PCBA service must be able to assemble both groups on one line, from fine-pitch IC packages to inserted DIP components.

Process Decisions That Keep SMT and Through-Hole Zones Reliable on the Same Board

Reflow and wave soldering both apply heat to the same laminated PCB, so the assembly order controls whether one set of joints survives while the other is being formed. The engineering review must address which side is soldered first, how the completed side is protected, and how much heat the through-hole process is allowed to apply near already-soldered SMT joints.

1. The Assembly Sequence Should Protect Reflow-Soldered SMT Pads from Later Through-Hole Handling

The normal sequence for a mixed board is solder paste printing, SMT placement, reflow soldering, and inspection, followed by through-hole insertion and wave soldering. That order allows the dense SMT side to become a complete, inspected structure before heavy connectors or relays are inserted. If DIP leads were inserted before the SMT reflow step, the tall components would interfere with solder paste printing and with the fine-pitch placement required for QFN, QFP, and similar packages. Reflow soldering also has component temperature limits, and the profile must stay within the limit of the most sensitive package on the board. Texas Instruments AN-1028 explains that maximum reflow temperature is a design constraint, not a value that can be raised to make a difficult board easier to solder. On a mixed board, the SMT side must also survive the board support, handling, and additional heat that occur during through-hole soldering. The process plan should treat the reflowed SMT zone as a finished structure and arrange DIP insertion so that it does not bend or overstress those joints.

2. Wave Soldering Needs Enough Thermal Input for the Plated Barrel Without Damaging Nearby SMT Joints

Wave soldering must balance two opposing requirements. The solder wave has to deliver enough heat and flux to wet the lead and fill the plated barrel, especially on thicker boards and around components with high thermal mass such as transformers, relays, and heavy connectors. At the same time, the underside of the board may already contain reflowed SMT joints. If the preheat stage or the wave contact applies too much heat to those areas, the SMT joints can be thermally damaged. If the heat is too low, the through-hole joint can have poor fill or incomplete wetting. The correct balance is not a universal formula. It depends on board thickness, copper plating inside the hole, component thermal mass, flux conditions, and the actual distance between DIP components and nearby SMT parts. Some through-hole components are better soldered with selective soldering or a dedicated pallet rather than full wave contact. These decisions require an engineering review of the physical board before the assembly line determines which DIP components can be wave soldered together and how the SMT side will be shielded.

Design and Documentation Needed Before a Custom SMT/DIP Assembly Run Starts

A mixed-technology board cannot be quoted reliably from a netlist or from a short component description. The service needs to know which components are SMT, which are through-hole, and where process conflicts are likely. Gerber files and drill data define the copper structure: SMT land patterns, solder mask openings, drilled hole sizes, and the clearance between surface-mount pads and through-hole pads. The bill of materials must include exact manufacturer part numbers, package types, reference designators, and approved alternates. On a board with a QFN MCU and a DIP connector, an alternate part may look similar in the BOM but require a different footprint or a different through-hole soldering method. Approved alternates prevent procurement and assembly teams from making assumptions that could disrupt the process order. The assembly drawing adds the information the BOM is separate from: pin-one orientation for ICs, polarity for polarized components, mechanical mounting details, parts inserted from the secondary side, and clearance limits around the DIP zone. It also communicates how the board should be supported during through-hole insertion and wave soldering. A mixed board therefore needs a documentation package built for a dual-process assembly line: Gerber data for the physical pads and holes, a BOM for exact component identity and sourcing, and an assembly drawing for build intent. Maxipcb’s PCBA service follows this path. Its assembly line supports SMT, DIP wave soldering, and reflow soldering, with package coverage from DIP through SOT/SOP/QFP/BGA/QFN/DFN. Mixed-technology boards can be quoted after a DFM review of the Gerber data, BOM, and assembly drawing, which is the stage where process conflicts should be caught before the first assembled unit.

Conclusion

A mixed-technology board is one electrical assembly with two different solder joint types. SMT is the right choice for dense ICs and small passives. DIP is the right choice for connectors and power components that need mechanical retention and a larger conductive path. The PCBA service selected for that board must be able to reflow the SMT side first, protect it during through-hole handling, and deliver enough thermal input to fill the plated barrel during wave soldering. When preparing a mixed board, submit the Gerber files, a complete BOM with manufacturer part numbers and approved alternates, and the assembly drawing for review. Confirm the proposed assembly sequence, the through-hole soldering method for each DIP component, and how the SMT side is protected. A service that reviews those files before quoting is more likely to deliver a working board with both joint types intact.

FAQ

Q:Why would a custom PCB assembly run need both SMT and DIP on the same board?

A:The two package families exist for different physical reasons. Dense ICs, memory, and small passives are surface-mount parts that can be placed and reflowed efficiently, while connectors, relays, transformers, terminal blocks, and other parts that carry higher current or face repeated mechanical stress are more reliable as through-hole components because their leads are soldered inside a plated barrel. Many industrial, power, and measurement boards therefore combine reflowed SMT zones with wave-soldered through-hole zones on the same PCB.

Q:What is the usual assembly order for a mixed-technology board with SMT and through-hole parts?

A:The common sequence is solder paste printing, SMT placement and reflow, inspection, through-hole insertion, and then wave soldering. This order allows the dense SMT side to become a finished, inspected structure before heavy DIP components are inserted. It also prevents through-hole leads from interfering with paste printing and fine-pitch placement, and it gives the final wave soldering step access to the plated barrels around the inserted leads.

Q:What files does a PCBA service need to assess an SMT and DIP mixed assembly project?

A:The core package is Gerber data, an accurate BOM, and an assembly drawing. Gerber and drill files define SMT land patterns, solder mask openings, hole sizes, and clearance around mixed-technology areas. The BOM needs exact manufacturer part numbers, package types, reference designators, and approved alternates. The assembly drawing shows polarity, pin-one orientation, mechanical insertion details, and any special through-hole requirements. These files allow the service to run a DFM review before quoting the mixed assembly.

Sources / References

Texas Instruments AN-1028 Maximum Solder Reflow Temperature for Surface Mount

Analog Devices AN-772: A Design and Manufacturing Guide for the Lead Frame Chip Scale Package

STMicroelectronics AN2639 Solder Pad Recommendations for Surface Mount Devices

Related Examples

Maxipcb PCB Assembly Service

Previous
Multilayer pcb prototyping and 4 layer prototype board thickness ranges
Read More
Next
Prototype PCB Assembly Service With DFM Review and Component Sourcing
Read More